Nathan James 12402 Vincent Pendant Light Fixture Instructions

Nathan James 12402 Vincent Pendant Light Fixture

Product Information

The Vincent Pendant Light (SKU 12402) is a lighting fixture that can be installed in any indoor room. The product comes with a ceiling plate, stems, a fixture, a socket unit, a glass shade, decorative screws, junction box screws, a crossbar, a finial nut, and wire connectors. The product has been tested to meet specific safety measures and comes with a free lifetime warranty. The estimated time for assembly is 25 minutes, and the product should not be modified in any way.

Product Usage Instructions

1. Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have occurred during shipping. If there is a defect in the wire, do not attempt installation.
2. Disconnect the power by turning off the circuit breaker or by removing the appropriate fuse at the fuse box before starting the installation. Turning the power off at the switch is NOT SUFFICIENT to prevent electrical shock.
3. Assemble the product according to the instructions provided. Do not use power tools and do not over tighten screws and bolts to avoid stripping.
4. After assembly, inspect the product carefully before use.
5. Do not use the product for commercial purposes, leave spilled liquid on the fixture, use the light fixture if damaged, make temporary repairs, or use it outdoors.

Pre-Installation

1. Remove decorative screws (8) from the fixture (5).
2. Separate the crossbar (B) from the ceiling plate (1) by removing the finial nuts (C).
3. Thread the socket unit (6) onto the fixture (5) and tighten 100%.
4. Twist the 12 stem (4) onto the fixture (5) and tighten 100%.
5. Add the 6 & 12 stems (2) and (3) to the top of the fixture (to your desired length) and tighten 100%.
6. Thread on the ceiling plate (1) at the very top and tighten 100%.
7. Read all instructions prior to beginning assembly.
8. To avoid damaging this product, assemble it on a soft, non-abrasive surface such as carpet or cardboard.
9. Keep the receipt and these instructions for proof of purchase.
10. Suggested Bulb: ST19 Vintage LED 60 Watt Equivalent | E26 Medium Base | Dimmable (not included)
11. Fixture Max Wattage: 60W

Let’s build the Vincent Pendant Light SKU 12402

Scan me!

• Inspiration
• Digital Instructions
• Free Lifetime Warranty

Ok, let’s get rolling
This should be easy, just follow our instructions and you will be back to Netflix in no time.

Estimated time for assembly: 25:00

What you need

• Your favorite snack or energy bar (Save the bubbly for once your fixture is safely installed!)
• Use the packaging carton as a working surface to prevent product damage during assembly

Do not use a drill

 |

Description

|

Qty

---|---|---
1| Ceiling Plate| 1
2

__

| 6” Stem| 2
3| 12” Stem| 1
4| 12” Stem| 1
5| Fixture| 1
6

__

| Socket Unit| 1
7| Glass Shade| 1
8| Decorative Screw| 2
A| Junction Box Screws M4*26mm| 2
B| Cross Bar| 1
C| Finial Nut| 2
D| Wire Connectors| 3

Safety first, fun later

Safe use of this product starts with you.
Use this light fixture responsibly with the primary concern for your safety. Follow assembly instructions carefully and inspect product upon receipt and each use. Nathan James and its parent companies cannot be held legally responsible for any injuries or death resulted from failure to follow instructions or improper use of this product.

Proper use

• DO NOT use for commercial purposes
• DO NOT leave spilled liquid on fixture
• DO NOT use light fixture if damaged
• DO NOT make temporary repairs
• DO NOT use outdoors

WARNING
Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have occurred during shipping. If there is a defect in the wire, do not attempt installation. Please reach out to our Customer Happiness team at help@nathanjames.com or 1-866-619-1004

WARNING: RISK OF ELECTRIC SHOCK
Before starting the installation, disconnect the power by turning off the circuit breaker or by removing the appropriate fuse at the fuse box. Turning the power off at the switch is NOT SUFFICIENT to prevent electrical shock. PLEASE CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL QUESTIONS.

The goods

IMPORTANT

1. Do not tighten bolts / screws completely until all bolts / screws are lined up and inserted into holes.
2. Do not over tighten screws and bolts to avoid stripping.
3. Please use hand tools to assemble this product. Do not use power tools.

Installation

Step 1
Let’s get this thing fired up!Remove Decorative Screws (8) from the Fixture (5).

Step 2
Separate the Cross Bar (B) from the Ceiling Plate (1) by removing the Finial Nuts (C).

Step 3
Let’s get this thing fired up! Begin by threading the Socket Unit (6) onto the Fixture (5) and tighten 100%.

Step 4
Twist the 12” Stem (4) onto the Fixture (5) and tighten 100%.

Step 5
Add the 6” & 12” Stems (2) and (3) to the top of Fixture (to your desired length) and tighten 100%.
We’re five steps in now! Cue the party music This would be a great time to break out the chips and salsa (if you haven’t already).

Step 6
Once you’ve added the correct number of 6” & 12” Stems to reach your desired length, go ahead and thread on the Ceiling Plate (1) at the very top. Tighten 100%!

Step 7
Install the Cross Bar (B) to your pre-installed Electrical Box.

Note : Be sure that you are only making the connections to a 120V 60Hz AC circuit. If you do not have a pre-existing electrical box, we strongly advise using a certified electrician.

Step 8
Wrap the Ground Wire from the Ceiling Plate around the Grounding Screw on the Cross Bar. Secure by tightening the screw.

Step 9

• Use the Wire Connectors (D) to connect the matching colored wires. (White to White, Black to Black & Ground to Ground).
• Once complete, tuck the excess wire into the Electrical Box.
• Would you believe us if we told you there are only three steps left?

Step 10
Secure the Ceiling Plate (1) (& the rest of light fixture) to the Cross Bar (B) on your pre-installed Electrical Box using the Finial Nuts (C).

To properly fasten the Finial Caps (C), thread in or out to adjust for proper threading length.

Step 11
Secure the Glass Shade (7) within the Fixture (5) by lining up their corresponding holes before threading the Decorative Screws (8) through the threaded holes in the Fixture (5). It’s all coming together!

Step 12
Install light bulb (not included) and voila! Let there be light!

We recommend using 1 ST19 Type light bulb. 120V 60Hz AC only.

Troubleshooting

Contact a qualified electrician or reach out to our Customer Happiness team at help@nathanjames.com or 1-866-619-1004.

Questions? Don’t worry, we’ve got the answers

• What other light bulbs can fit in this light?
  The bulb must not be greater than the max wattage for the fixture. It must match the base size, and the diameter of any area of the bulb should be less than diameter of any area of shade, so that it can fit.

• Can I use an LED light bulb?
  Yes, so long that the base size matches and the diameter of any area of bulb is less than diameter of any area of shade, so that it can fit.

• Is this UL/ETL certified?
  Yes, all our products are either UL or ETL.

• Do I need an electrician to set up the hardwire?
  We recommend using a certified electrician for all hardwiring, although all of our fixtures can be set up without an electrician, as long as you are replacing an existing fixture or have an existing junction box ready for a fixture installation. ENSURE POWER IS OFF WHEN INSTALLING. For all new constructions, please use a certified electrician.

• Can I retrofit this hard-wired to a plug-in or vice-versa?
  Yes, a plug-in fixture can be turned into a hardwire fixture and a hardwire fixture can become a plug-in fixture. For many products we will provide all the necessary hardware to make these changes, if not, you will need to purchase the necessary hardware.

• Is this light compatible outside North America?
  Our lighting is only warranted in Canada and the United States.

• What do I do if the product is not working?
  Try a different light bulb and confirm proper installation.

• Can these lights work on a dimmer?
  Dimmability is related to the light bulb and the wall switch, not the light fixture. All our hardwire fixtures are compatible with dimmable light bulbs. We recommend using a dimmer switch, as it extends the life of the bulb and allows for energy saving and great ambiance. If using a LED bulb, please ensure both your LED bulb and dimmer switch are compatible.

• Can I use the fixture outdoors?
  No, this product was designed to be used indoors only in dry locations.

No heartburn,when we handle the return
Give us a call 1-866-619-1004 or shoot us a message at help@nathanjames.com we will issue you a free replacement with zero hassle.

We really don’t want you to go through the hassle of re-packaging your item and sending it back, because let’s be honest…nobody has time for that.

We are only in business if you’re happy For starters, thanks for being you.

We do our best to ensure your lighting arrives without any problems, but occasionally mistakes happen—as humans we are imperfect beings. In the event that a part is damaged or missing, we will be more than happy to provide you with replacement part(s) for free.

• Toll-free at 1-866-619-1004
• Help@nathanjames.com
• Nathanjames.com/help

Warranty

This product comes with a lifetime warranty from the date of purchase. Please use your phone to scan the QR code to register your product or visit https://goo.gl/i9dk3q

Did we do alright? Please spread the love!
If you are happy with your product, tell your friends and family about us or even better leave us a review online. Spreading the word gives us the opportunity to make more people happy and keep our
prices low for your next purchase.

References

• Support : Nathan James
• Product Warranty | Nathan James

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>