GOODWE GR-A1F-20 Photovoltaic PV Rapid Shutdown Equipment Installation Guide
- May 15, 2024
- GOODWE
Table of Contents
GOODWE GR-A1F-20 Photovoltaic PV Rapid Shutdown Equipment Installation
Guide
Safety Precaution
General Disclaimer
- The information in this guide is subject to change due to product updates or other This guide cannot replace the safety instructions or labels on the device unless otherwise specified. All descriptions here are for guidance only.
- Before installations, read through the documents of the device, inverter, and PV module tolearn about the product and the precautions.
- All operations should be performed by trained and knowledgeable technicians who are familiar with local standards and safety
- Use insulating tools and wear personal protective equipment when installing or operating the device to ensure personal
- Check the deliverables for correct model, complete contents, and intact Contact after-sales service if any damage is found or any component is missing.
- Strictly follow the installation, operation, and configuration instructions in this The manufacturer shall not be liable for device damage or personal injury if you do not follow the instructions. For more warrant information, please visit https://en.goodwe.com/warranty.
Safety Disclaimer
- Make sure the voltage and the current of the PV module match the device
- Disconnect the DC switch and AC switch of the inverter before
- Make sure the PV connectors connected to the device are of the same type as the input and output connectors of the
- Do not short-circuit the output Otherwise, the device may be damaged.
- After installing the device, turn on the AC switch of the inverter first and then the DCOtherwise, the system may fail to start.
- To avoid interfering the rapid shutdown function, do not install transmitters from other manufacturers to the PV cable during the use of the RSD
- It is recommended to use the corresponding GoodWe
- Recommended install the device in a sheltered place to avoid direct sunlight, rain, and
- Connect the device to the PV modules first and then to the
- Measure the PV input voltage of the inverter to confirm that the number of PV modulesconnected is the same as the actual number of modules.
- Measure the PV modules using a current clamp to confirm that each module has currentoutput.
- Measure the input current and output current of the device to confirm that the input and output caurrent are the same.
EU Declaration of Conformity
GoodWe Technologies Co., Ltd. hereby declares that the inverter without wireless communication modules sold in the European market meets the requirements of the following directives:
- Electromagnetic compatibility Directive 2014/30/EU (EMC)
- Electrical Apparatus Low Voltage Directive 2014/35/EU (LVD)
- Restrictions of Hazardous Substances Directive 2011/65/EU and (EU) 2015/863 (RoHS)Quick Installation Guide V1.0-2023-06-15
- Waste Electrical and Electronic Equipment 2012/19/EU
- Registration, Evaluation, Authorization and Restriction of Chemicals (EC) No 1907/2006 (REACH)
You can download the EU Declaration of Conformity on https://en.goodwe.com.
The RSD maintains the modules working by continuously receiving a heartbeat signal from a transmitter. The transmitter can be external or integrated into the inverter. In case of an emergency, enable the external initiator to shut down the transmitter. The RSD will stop working and shut down the modules after the transmitter signal absenting.
| Model | GR-A1F-20 | GR-B1F-20 |
|---|---|---|
| Operating Voltage Range (V) | 8~80 Per channel | |
| Rated Input Current (A) | 22 | |
| Mode of Communication | PLC |
Operating Temperature Range
(℃)
| -40~+85°C
Ingress Protection Rating| IP68/UL Type 6P
Maximum System Voltage (V)| 1100| 1500
Security Certification| NEC 2017&2020&2023 (690.12); UL1741; CSA C22.2 No.
330; IEC/EN62109-1;
EMC Certification| FCC Part15; ICES-003; IEC/EN61000-6-1/-2/-3/-4
Whether the SunSpec Protocol is Supported| Yes
Dimension (W×H×D mm)| 140×37×23 mm
Cable Length (m)
| ① I②n: 0.2m, Out: 0.8m (Integrated Junction Box) In: 1.2m, Out: 0.8m (Triad Junction Box)
or Customize
Connector| MC4 or Customize