Install Guide

BR31 Wireless Door Sensor Document
Document Details
V1.0(20210929)
(V1.0 first published 20210929)
Firmware
The firmware version can be verified on Verkada Command command.verkada.com.

Introduction

What’s in the box

What you’ll need

• BH61 Wireless Alarm Hub Please note: Add your BH61 Wireless Alarm Hub
• A working internet connection to Command before setting up your Wireless
• Smartphone or laptop Door Sensor.

• 2phillips driver (screwdriver or power drill)

• 0.1 inch (2.5mm) drill bit for pilot holes

Connect

• To register your product, please proceed to: verkada.com/start

Sensor Overview

LED Behavior

Test mode
To enable test mode, press the top button. While in test mode, the green LED will:

• turn on when the sensor is separated from the magnet (door opened)
• turn off when the sensor is brought close to the magnet (door closed).
  After ten minutes in test mode, the device will return to normal operation.

Normal operation
While in normal operation, the green LED will:

• NOT turn on when the sensor is separated from the magnet
• flash rapidly three times every two minutes to indicate low battery

Mounting 1/5

Use the provided T10 Security Torx L-key to unscrew the security screw at the bottom of the product. Swing the sensor module out and disengaging the hooks at the top of the sensor mount.
Remove the battery pull tabs. Mounting 2/5
Engage the hooks at the top of the sensor mount and swing the sensor module into place. While the device is in test mode, place the sensor module and the magnet piece on the desired surfaces to see if the sensor registers a closed- door (the sensor module’s LED will turn off when it senses a closed door).
With a screwdriver, make pilot holes and screw the sensor mount into place. Mounting3/5

Use the provided T10 Security Torx L-key to unscrew the security screw at the bottom of the magnet. Swing the magnet cover out and disengaging the hook at the top of the magnet cover. Make sure to align the “align” mark and screw the magnet piece onto the desired surface.

Mounting 4/5
Engage the hooks at the top of the sensor mount and swing the sensor module into place.Use the provided T10 Security Torx 1-key to secure the security screw in place.

Mounting 5/5
Engage the hook at the top of the magnet cover and swing the magnet cover into place. Use the provided T10 Security Torx L-key to secure the security screw in place. Appendix

BR31 Compliance

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  To assure continued compliance, any changes or modifications not expressly approved by the patty responsible for compliance may void the users authority to operate his equipment. (Example – use only shielded interface cables when connecting to computer or peripheral devices)
  This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions.
  (1) This device may not cause harmful interference, and
  (2) This device must accept any interference received, including interference that may cause undesired operation.
  IMPORTANT NOTE:
  Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

IC Statement
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two Statement conditions:
(1) This device may not cause interference;
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

Appendix Support
Thank you for purchasing this Verkada product. If for any reason things don’t work right or you need assistance, please contact us immediately.
verkada.com/support Sincerely, The Verkada Team
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
sales@verkada.com
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>