rapidline GL305-1 GO Steel Lockers 1 Door Instruction Manual

rapidline GL305-1 GO Steel Lockers 1 Door

Product Information

Specifications

• Product Code: GL305/1 & GL380/1
• Product Name: GO Steel Lockers – 1 Door
• Assembly Time Required: 25 minutes
• Tools Required: Pop Rivet Gun (*Tools are not included)
• Skill Level Required: Easy

FAQ

• Q: Can I assemble the locker alone?
• A: While it is possible to assemble the locker alone, it is recommended to have two persons for easier and quicker assembly.
• Q: Do I need to purchase tools separately for assembly?
• A: Yes, you will need a pop rivet gun for assembly. Tools are not included with the product.
• Q: Is there a warranty for this product?
• A: Please refer to the product warranty information provided by the manufacturer.

ASSEMBLY INSTRUCTIONS

• Product Code: GL305/1 & GL380/1
• Product Name: GO Steel Lockers – 1 Door

TIME REQUIRED:

• 25 minutes

TOOLS REQUIRED:

• Pop Rivet Gun
• Tools are not included.

SKILL REQUIRED:

• Easy Hard.
• The Assembly Skill Rating is a 5-point system that shows the degree of effort needed in assembling a specific product.
• With 1 being easy for the average person and 5 requiring an expert. For most products, two persons are recommended.

NOTE

• As this is a commercial product, some intermediate skills may be required.
• No pre-drill holes or markings are provided on our tables or desktops.
• Please check you have all the hardware before assembling.
• If you are missing any hardware, please contact your Rapidline reseller. Please ensure you have the name of the item, required hardware part and quantity.
• Please retain your receipt as proof of purchase to validate your warranty.
• Assemble on a clean,, smooth surface such as a rug or carpet to avoid parts from being scratched.
• Remove all wrapping materials, including staples and packing straps before you start to assemble
• Keep all hardware parts out of reach of children.

CAUTION

• Heavy product. Do not attempt to lift or move without help
• Do not tighten screws and bolts until completely assembled.
• Do not use this product unless all bolts and screws are firmly secured and tightened.

WARNING

• If parts are missing, broken, damaged or worn stop using the product until all repairs are made.
• Failure to follow these warnings could result in serious injury.

GC 305 / 1,2 AND 4-DOOR LOCKERS ASSEMBLY INSTRUCTIONS

PARTS

Installation Instructions

STEP 1

• Place the LH Side Panel (With CAM SLOT on the Flat surface(Assly Table) and rivet the back panel with the panel as shown except the two top holes (which will be riveted along with the Top panel) rivet from outside to inside.

STEP 2

• Rivet the shelf with the back panel as shown in the drawing (rivet from outside to inside)

STEP 3

• Insert the top flange of the bottom front into the bottom tray and rivet as shown in the drawing (seperate sub-assembly)

STEP 4

1. Rivet the SHELF(Shelves) with the back panel as shown.
2. Rivet the bottom tray and bottom front assembly with the back panels as shown.
3. Rivet the bottom front with the side.

STEP 5

1. Place the RH side on the Back, Shelf and Bottom Tray as shown.
2. Rivet the side with the back on all the holes except the top hole and also rivet the side with the shelves and bottom tray as shown.

STEP 6

1. Fix the Top as shown and Rivet with the back and sides as shown.
2. Fix COAT HOOK in 2-door locker on top and shelf (applicable to 2-door locker only)
3. Flip the Locker on Its back as shown (Back touches the ground) for rivetting the Shelf and bottom tray with the LH Side.

STEP 7

1. Rivet the LH side the Shelves and the Bottom Tray as shown.
2. Again Flip around the Locker in Its RH side as shown for DOOR FIXING.

STEP 8

1. Position the door in the hinge slots of the RH side as shown rivet the door using counter sunk reverts and then lift erect the locker.

STEP 9

1. Fix the Coat hanger in the 1 door locker as shown.
2. Fix the Coat hanger in the 2-door locker in step no 6 (Applicable to 2-door locker only)

STEP 10

1. Check the lock for unlock and lock condition before fixing it in hand.
2. Insert the lock in the unlock condition and press completely as shown.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>