LEDALITE ID-33 Shine and Silk Space Definition Instruction Manual
- May 15, 2024
- LEDALITE
Table of Contents
LEDALITE ID-33 Shine and Silk Space Definition
Specifications
- Product: Recessed Shine & SilkSpace Definition ID-33 & ID-42
- Installation: Standalone, T-Grid, and drywall ceilings
- Electrical: Class A digital device compliant with FCC Rules
Preparing Fixtures for Mounting
- Bend the mounting tab to fit the T-Grid height.
- Adjust the height of the tab accordingly.
- If using a 20×60 T-Grid ceiling, attach filler panels to the housing ends with supplied screws.
Mounting in a T-Grid Ceiling
- Lay the fixture into the T-Grid.
- Bend tabs flush against the T-Grid to clear for ceiling tile.
- Fasten the fixture to the T-Grid using #8×1/4 sheet metal screws and hanger wires as per local building codes.
Mounting in a Drywall Ceiling
- Cut a hole in the drywall as per provided dimensions.
- Insert the mounting frame into the hole and secure it.
- Secure the mounting frame by screwing it to a wood frame or attaching hanger wires.
Making Electrical Connections & Lens Installation
- Make all electrical connections to the fixture.
- For flex whip option, follow step 11 for installation.
- To install lenses, remove the cardboard shipping insert and slide the second lens to enclose in the fixture cavity.
FAQ
Q: What should I do if I encounter difficulties during installation?
A: If you face challenges during installation, please refer to the provided
layout drawings and ensure you follow all instructions mb7uy
carefully. If issues persist, contact Ledalite customer support for
assistance.
Recessed
Shine & SilkSpace Definition
ID-33 & ID-42
System Overview
These instructions review how to install recessed Shine and SilkSpace Definition fixtures. Please refer to layout drawings supplied by Ledalite in conjunction with these installation instructions. The graphic below shows the components required to install a run of Shine and SilkSpace Definition recessed fixtures in T-Grid and drywall ceilings.
IMPORTANT : Read all instructions including fixture/sensor wiring AND mechanical details before beginning installation.
Standalone Installation Instructions Imperial & Metric Sizes
Preparing fixtures for mounting
-
Bend out the mounting tab 90° on each corner.
-
Use side cutters to adjust each tab to a height of the T-Grid.
-
If installing in a 20”x60” T-Grid ceiling, attach filler panels to ends of the housing using supplied screws, as shown above.
-
Lay fixture into T-Grid.
-
Bend tabs flush against T-Grid in order to clear for ceiling tile.
-
Use #8×1/4” sheet metal screws to fasten fixture to T-Grid and use a hanger wire to tie off appropriately in accordance with local building codes. (Screws and hanger wires supplied by others).
-
Cut a hole in the drywall according to the dimensions in the table above.
-
Insert mounting frame into hole and secure as showing in step 9.
-
Secure mounting frame by screwing to wood frame or attaching hanger wires.
Standalone Installation Instructions -
Make all electrical connections to the fixture. For flex whip option, see step 11.
-
Optional flex whip is prewired inside fixture. Remove packaging and insert snap-in fitting into wiring cover and complete electrical connections at other end of whip.
-
Remove & recycle cardboard shipping insert holding lenses in place.
-
Slide second lens across to enclose in fixture cavity.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
ATTENTION : Install in accordance with local and national building and electric codes.
© 2021 Signify Holding. All rights reserved. The information provided herein is subject to change, without notice. Signify does not give any representation or warranty as to the accuracy or completeness of the information included herein and shall not be liable for any action in reliance thereon. The information presented in this document is not intended as any commercial offer and does not form part of any quotation or contract, unless otherwise agreed by Signify.
Signify North America Corporation 400 Crossing Blvd, Suite 600 Bridgewater, NJ
08807 Telephone: 855-486-2216
Signify Canada Ltd. 281 Hillmount Road, Markham, ON, Canada L6C 2S3 Telephone:
800-668-9008
All trademarks are owned by Signify Holding or their respective owners. www.signify.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>