LEDALITE ID-7408 Sync Wall LED Light Instruction Manual

LEDALITE ID-7408 Sync Wall LED Light

System Overview

These instructions review how to install Sync wall mount fixtures. Sync 4 ftand 8 ftmodules can be installed as individual standalone units, or they can be joined together to create continuous rows. The graphic below shows the components required to install a typical row of Sync wall mount fixtures .

TOOLS REQUIRED: Stubby Phillips screwdriver, 3/8 ” nut driver.

Standalone or continuous run configurations

Module Lengths
Syncwall mount systems come in 4ft and 8ft modules. Overall module lengths are shown to the right. Module lengths do not include endcaps.

Endcaps
Add two endcaps to the overall length of each row.

Mount Spacing

©Mounts variable within 2″ – 5″ of end or joint. On 8ft module, an additional mount to be located within 2″ – 5″ of the center of the module. ©Maximum distance between mounts is 48″. Note: Fixture is flush with the wall .

Row Configurations
The tables below indicate how 4ft and 8ft modules can be combined tocreate continuous rows of various lengths.

IMPORTANT: Read all instructions at least once prior to beginning installation. All mount brackets must be secured towall structure (eg. studs or cross-braces).This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

1. Install utility box and utility box cover
   Determine power feed location and install 2″x4″ utility box (supplied by others) parallel with the fixture. Complete connections at utility box with supplied power cord. Attach cover bracket using supplied hardware. Punch power access hole in supplied cover, feed power cord through and attach strain relief on wall side. Attach
   cover using supplied painted hardware.
   NOTE: The bottom of the utility box should be in line with the bottom of wall brackets.
   

2. Install wall brackets
   Determine fixture mounting location and secure wall brackets to structure using appropriate fasteners (two per bracket, supplied by others). 4ft fixtures: Require two bracket assemblies; 8ft fixtures: Require three bracket assemblies. Brackets must be installed a maximum of5″ from the end of the fixture (on 8ft fixture, the third bracket can be 5″ of either side of the in- row cross plate).
   NOTE: Mounted fixture(s) will sit approximately /4″ above the top edge of the bracket assembly.

3. Unpack / Prepare fixtures
   Arrange boxed fixtures on floor in specified locations; remove fixtures from boxes; remove plastic from fixtures. Cap all unnecessary power feed holes at the back of fixture(s) using supplied 1/2″ plugs.

4. Remove Top Reflector
   Shift top reflector to the left and then remove the reflector.

5. Remove Front Reflector
   Remove the screws holding the front reflector and then remove the front reflector.

6. Raise Fixture and Engage on Wall Brackets****  

With 2 people, raise the fixture into position and engage it on hooks located on top of wall brackets, then rotate it down into position. Secure bracket using supplied hardware.
POWER LOCATIONS: Prior to an engaging the fixture in mounting brackets, feed the installed power cord through the access hole at back of the fixture.

7. Access Wiring / Remove Pan
   To access wiring, remove screw from top pan and lift pan off. Apply strain relief to power cord.
   NOTE: Care should be taken when lifting up top reflector to avoid disconnecting internal wiring.
   

8. Complete electrical connections
   Complete electrical connections using wire nuts (supplied by others). Re- install pan and hardware removed in STEP 6.

9. Level and the secure first fixture
   LEVEL: Using 5/16″ hex nut driver, level the fixture by adjusting the tilt screw.
   SECURE: Secure fixture to wall bracket assemblies by tightening the lock screw.

10. Install and join additional fixtures to create row
    With two people, raise the second fixture and engage on mounting brackets (see STEP 4). At joint, remember to insert black gasket.

11. Complete electrical connection at joints
    Complete in-row electrical connections.
    NON-POWER LOCATIONS: Use supplied quick-wire connectors. Tuck wires into wire cavity.
    POWER LOCATIONS: Remove installed quick-wire connectors and complete electrical connections using wire nuts (supplied by others). Tuck wires into wiring cavity.
    NOTE: Use the smallest appropriate wire nuts.

12. Level and secure additional fixture
    Level the second fixture by adjusting the tilt screw (see step 8). Slide the second fixture flush against first fixture and secure the joint using supplied nut and bolt hardware (requires 3/8″ nut drivers). Secure fixture to wall brackets by tightening the lock screw at each bracket location (see step 8). Repeat steps 8-10 for each additional fixture(s) in row.

13. Install Endcaps
    Attach endcap to first and last module in each row using supplied hardware.
    IMPORTANT: Do not over-tighten endcap fasteners. Ledalite recommends tightening fasteners by hand. When nut is flush with crossplate, turn an additional 1/4 turn.

14. Re-install Front Reflector
    Re-install front reflector using short (stubby) screwdriver.

15. Install Light Guide and and Reinstall Top Reflector
    Identify smooth side of the Light Guide and ensure it is installed smooth side DOWN. Install Light Guide panel into LED fixture after joining and wiring is complete. Ensure panel is seated correctly as shown above. Final Step: Install the top reflector and shift into place.

Sensor in Rows

Single Sensor Controlling Whole Row

1. Purple & brown (or purple & grey/pink) control wires MUST be connected between fixtures. Note :
   • A maximum of 8 drivers can be wired to 8 sensors; confirm fixture driver count with factory.

Multiple Sensors Controlling Separates Zones in a Row

1. Purple & brown (or purple & grey/pink) control wires MUST NOT be connected between zones.

Notes :

• A maximum of 8 drivers can be wired to one sensor; confirm fixture driver count with factory.
• Only one sensor is allowed on a wired zone. (Sensors can be paired together wirelessly via a mobile app).

Sensor Spacing

• For correct operation, sensor should be placed a minimum distance of 8ft apart.
• Wireless sensor should be placed no further than 40ft apart for good wireless signal connection.

Occupancy Sensor Coverage

Note: Longer dimension of detection area (Y1, Y2) is parallel to longer dimension of the luminaire.

Daylight Sensor
The light sensor measures the total amount of light in a circular field of approximately 80% of the PIR detection area. The following aspects should be observed during installation:

• Minimum distance from the window = 2ft (0.6m).
• Prevent light reflections from outside entering the sensor (for example sunlight reflection on a car hood) as this will lead to incorrect light regulation.

As a guideline the formula 0.72 X H can be used to calculate the minimum distance between the window and sensor whereby H is the height from the bottom of the window to the sensor.

The detection area for the movement sensor can be roughly divided into two parts;

• Minor movements (person moving = 3ft/s or 0.9m/s).
• Major movements (person moving = 3ft/s or 0.9m/s).

Photosensor spatial response

ATTENTION: Install in accordance with national and local building and electrical codes. 2019 Signify Holding. All rights are reserved. Reproduction in whole or part is prohibited without the written consent of the copyright owner. Phone: 604.888.6811Web: ledalite.com/products Revision D Signify North America Corporation. 400 Crossing Blvd, Suite 600 Bridgewater, NJ 08807. Telephone: 855 486 2216 Signify Ca 2216 Signify Ca nada Ltd. 281 Hillmount Road, Markham, ON, Canada L6C 2S3. Telephone: 800 668 9008

References

• Indoor architectural lighting | Ledalite | Signify

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>