QUAD LOCK QL-3954-W Wireless Charger Head Instructions
- May 15, 2024
- QUAD LOCK
Table of Contents
QUAD LOCK QL-3954-W Wireless Charger Head
Specifications
- Model: QL-3954-W
- Wireless Charger Head
- TX/RX Frequency Range: 110-148KHz
- Manufacturer: Annex Products Pty Ltd, Australia
- Compliance: FCC Part 15, Directive 2014/53/EU, UK Radio
- Equipment Regulations SI 2017:1206
- Minimum Separation Distance: 20cm from the body
Product Usage Instructions
- Tighten: Apply a torque of 1Nm when assembling the Wireless Charger.
- Alignment: Align the ribs on the Top Cap with the ribs on the Wireless Charger.
- Attachment: Attach the Wireless Charger to a Quad Lock 360 MOUNT, ARM, or BASE for usage.
Important Notes
- Ensure a minimum distance of 20cm between the Wireless Charger and your body during the operation.
- Use only the supplied antenna to avoid interference issues.
- Avoid using third-party accessories containing metallic components near the device.
Declaration of Conformity
The product complies with FCC Rules, Directive 2014/53/EU, and UK Radio Equipment Regulations. For further details, visit the internet addresses provided in the manual.
FCC Compliance
Operation of this device should not cause harmful interference and must accept any interference received. Maintain a minimum separation distance of 20cm between the device and your body. Annex Products Pty Ltd, Australia, declares that the product “Wireless Charger Head, Model No. QL-3954-W”, complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: The “Wireless Charger Head” has been tested and found to comply with the limits for a Class B device, under Part 15 of the FCC Rules and has been assigned FCC ID: 2AOU9-QLH2. These limits are designed to provide reasonable protection against harmful interference. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced technician for help.
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. Use only the supplied antenna.
CAUTION: Any changes or modifications in the construction of these devices that are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device was tested for operations. To comply with RF exposure requirements, a minimum separation distance of 20cm must be maintained between the user’s body and the handset, including the antenna. Third-party belt clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or approved antenna.
This device complies with the essential requirements and other relevant provisions of Directive 2014/53/EU. All essential radio test suites have been carried out. This restriction will be applied to all Member States of the European Union. The device complies with RF specifications when the device is used at 20cm from your body
Declaration of Conformity
Hereby, Annex Products Pty Ltd declares that the product “Wireless Charger
Head” complies with Directives 2014/53/EU & 2011/65/EU. The full text of the
EU Declaration of Conformity is available at the following internet address:
https://www.quadlock.com.au/compliance
EU Declaration
The product meets essential requirements and relevant provisions of Directive
2014/53/EU. Radio tests have been conducted for compliance with RF
specifications.
UK Declaration
The device complies with UK Radio Equipment Regulations and relevant safety
regulations. Refer to the provided internet address for the full text of the
UK Declaration of Conformity. This device was tested for operations. To comply
with
RF exposure
requirements, a minimum separation distance of 20cm must be maintained between
the user’s body and the charger, including the antenna. The device complies
with the essential requirements and other relevant provisions of the UK Radio
Equipment Regulations SI 2017:1206 (as amended). 1. The device complies with
RF specifications when the device is used at 20cm from your body.
Declaration of Conformity
Hereby, Annex Products Pty Ltd declares that the product “Wireless Charger
Head” complies with the following Directives: Radio Equipment Regulations
2017, Electrical Equipment (Safety) Regulations 2016 and The Restriction of
the Use of Certain Hazardous Substances in Electrical and Electrical Equipment
2012. The full text of the UK Declaration of Conformity is available at the
following internet address: https://www.quadlock.com.au/compliance
Radiated H-Field (EU and UK Only)
- Radiated H-Field: 5.3 dBA/m (10m)
- TX/RX Frequency Range: 110-148KHz
INDUSTRIE CANADA
IC: 27134-QLH2
INDUSTRIE CANADA (IC: 27134-QLH2)
IC Caution
Radio Standards Specification RSS-Gen, issue 5
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions: (1) This device
may not cause interference. (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
RF exposure statement
The equipment complies with IC Radiation exposure limits set forth for
uncontrolled environments. This equipment should be installed and operated
with a minimum distance of 10cm between the radiator and your body.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>