QUAD LOCK QL-5764 Waterproof Wireless Charger User Guide

June 16, 2024
QUAD LOCK

QUAD LOCK Logo HEAD
1 2V-24V WATERPROOF
WIRELESSCHARGER

WHAT’S IN THE BOX

1x 12-24v Waterproof Wireless Charging Head
2x Cable grommet plugs
1x 3mm hex key
1x M5x35mm CSK head hex socket Screw
5x 5x200mm Nylon zip ties

INSTALLATION

QUAD LOCK QL 5764 Waterproof Wireless Charger -
INSTALLATION

WIRING DIAGRAM

QUAD LOCK QL 5764 Waterproof Wireless Charger - WIRING
DIAGRAM

LED STATES

| POWER ON/ STAND BY
---|---
| ERROR MODE
| CHARGING/ FULL CHARGE

INSTALLATION WITH GROMMET

QUAD LOCK QL 5764 Waterproof Wireless Charger -
GROMMET

CABLE FITMENT

USING CABLE TIES?
Recommend not to tighten the cable ties too much to avoid stressing the cables and causing damage.
Ensure there is some slack in the cable near the Wireless Charging Head to allow for ease of engaging / disengaging the phone on Wireless Charger.
Wireless Charger has a cable routing groove on the underside to hold the cable. CABLE CLEARANCE

Once the Wireless Charging Head is installed in the preferred orientation, push down on it to ensure the cable does not interfere with other devices or any operation (steering, breaking, etc).

ATTACHING YOUR PHONEQUAD LOCK QL 5764 Waterproof Wireless Charger -
PHONE DETACHING YOUR PHONE

QUAD LOCK QL 5764 Waterproof Wireless Charger - DETACHING YOUR
PHONE

Model No.: QL-5764

**** Annex Products Pty Ltd, Australia, declares that the product QL-5764 is in compliance with RED Directive (2014/53/EU) .
The CE certificate of conformity can be found at: www.quadlock.com.au/compliance
Annex Products Pty Ltd, Australia, declares that the product QL-5764 is in compliance with the following Directives: Radio Equipment Regulations 2017, Electrical Equipment (Safety) Regulations 2016 and The Restrictions of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment 2012.
The certificate of conformity can be found at: www.quadlock.com.au/compliance

Radiated H-Field -19.03 dBμA/m (@10m) (only for EU and UK)
TX/RX frequency range 120.0kHz – 126.4kHz (only for EU and UK)

FCC Compliance Statements
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2.  this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules and has been assigned FCC ID: 2AOU9-HWCH. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

RF Exposure Compliance
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

INDUSTRIE CANADA ( IC: 27134-HWCH )
IC Caution:
This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

  1. this device may not cause interference,
  2. this device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.

ISED Radiation Exposure statement
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.QUAD LOCK Logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals