eurowise Audi R8 V8 Supersport X-Pipe Exhaust Instructions

eurowise Audi R8 V8 Supersport X-Pipe Exhaust

Product Information

Specifications

• Product: Audi R8 V8 / V10 Exhaust
• Manufacturer: Eurowise
• Model: SuperSport X-Pipe Exhaust System
• Installation Location: 440 Springbrook Road, Charlotte, NC 28217
• Contact: 704-559-8100, info@eurowise.com
• Website: www.eurowise.com

Product Usage Instructions

Pre-Installation Preparations

• Before starting the installation process, ensure you have the necessary tools and equipment as specified in the PDF instructions.
• Also, make sure the vehicle is parked on a flat surface and the engine is cool.

Bumper and Exhaust Removal

• Refer to the attached PDF instructions for detailed steps on removing the bumper and the existing exhaust system from your Audi R8 V8 or V10.

Installing the Eurowise SuperSport X-Pipe Exhaust System

1. Follow the step-by-step instructions provided in the attached PDF for installing the new exhaust system.
2. Ensure all connections are secure and properly aligned before tightening any bolts or clamps.
3. Double-check that the exhaust is positioned correctly and does not interfere with any other components of the vehicle.

Post-Installation Checks

• After installation, start the vehicle and check for any leaks or unusual sounds.
• Make sure the exhaust system is functioning correctly and there are no issues with its operation.

FAQ

• Q: How do I contact Eurowise for product-related queries?
• A: You can contact Eurowise at 704-559-8100 or email them at info@eurowise.com. Additionally, you can visit their website at www.eurowise.com for more information.
• Q: What should I do if I encounter difficulties during installation?
• A: If you face any challenges during the installation process, it is recommended to reach out to Eurowise for assistance. They have a dedicated team to help customers with any product-related concerns.

PDF with photos attached to instructions as well. Please refer to the PDF instructions for only the bumper and exhaust removal and installation.

Audi R8 V8 Supersport X-Pipe Exhaust System.

Required Tools

• Commercial Lift (or Hydraulic Floor Jack &
• Stands) Socket Driver or Impact Wrench.
• 3” Socket Extension.
• Swiveling Socket Adaptor.
• 10mm & 13mm Sockets.
• 13mm Open-End Wrench.
• T-20, T-25, T-30 Torx Drivers/Bits.
• Flat-Head Screwdriver(Small).
• Cross-Head Screwdriver.
• Snap-Ring Pliers.
• Small Flashlight (Optional).

CAUTION

• Always allow the car to cool before performing any installation(s) or service(s) on it.
• Always be sure to work on an even and level surface when raising vehicle(s) with a jack, and support all raised vehicles with locked jack stands once elevated.
• Recommends that all installations be supervised or verified by a trained professional technician.
• Eurowise is not responsible for any personal injury or damage(s) sustained to a vehicle during the installation of aftermarket performance parts.

Instructions

1. Raise the car off of the ground and remove the rear wheels.
2. Remove (7) fasteners securing rear bumper tabs.
3. Remove the license plate and (2) fasteners beneath it securing the license plate bracket.
4. Locate and remove (2) fasteners tucked up inside of the overhang where the license plate lights are located.
5. Unclip and remove license plate lights.
6. Locate and remove (2) additional fasteners located inside license plate light housings.
7. Remove the upper rear body panel and unplug all wiring.
8. Remove (2) fasteners from the diffuser channel underneath both sides of the rear bumper assembly.
9. Remove rear under-body inlet covers.
10. Remove (4) fasteners near the front centre of the rear bumper diffuser panel.
11. Remove (4) fasteners from behind the grilles beneath each tail light.
12. Remove fasteners securing the rear upper trim panel.
13. Gently pull back the top of the rear bumper panel and unplug the wiring harness.
14. Remove the antenna connector from the left side of the panel.
15. Remove all fasteners securing rear fender liners to the body/chassis.
16. Remove rear fender liners.
17. Remove (2) fasteners securing the outer edge of the heat shield to the rear bumper on either side.
18. Locate and remove (2) fasteners securing the rear bumper to the upper body panel on either side.
19. Gently separate the rear bumper assembly and unplug the wiring harness.
20. Remove the rear bumper assembly.
21. Remove fasteners securing the passenger side engine bay trim panel.
22. Using a small flathead screwdriver, carefully pry the engine cover strut off of the mount.
23. Remove the reservoir cap and set aside.
24. Carefully pry back the trim panel and unplug the wires for the engine bay light.
25. Remove the trim panel.
26. Repeat steps 21 through 25 to remove the driver-side trim panel.
27. Pry off and remove the small plastic cover at the rear of the engine.
28. Unplug mass airflow meter wires from both sides of the intakes.
29. Loosen hose clamps enough to pull intake hoses off of the fittings.
30. Remove the mounting screw from the bottom of each side of the airbox.
31. Remove airbox.
32. Remove the (2) screws from the mounting tabs of the rear heat shield.
33. Remove fasteners from the outer lower heat shields on either side of the vehicle.
34. Remove mounting screws from the bumper support.
35. Remove the flanged hex nuts securing the outer lower heat shields to the bumper support.
36. Remove the flanged hex nut securing the outer lower heat shield to the frame/chassis and remove the heat shield.
37. Remove bumper support mounting bolts.
38. Free wiring harness from bumper support.
39. Remove bumper support.
40. Unplug tail light connections.
41. Remove exterior tail light mounting screws.
42. Remove hex nuts securing interior tail light mounting posts and remove tail lights.
43. Unplug vacuum lines from muffler valves.
44. Remove the fasteners securing the vacuum line brackets and move the vacuum lines out of the way.
45. Remove the fanged hex nut located up inside the top of the heat shield, above the exhaust outlets.
46. Remove lower muffler mounts.
47. Remove the upper muffler mounts.
48. Remove v-band clamps from flex joints.
49. Remove the fastener securing the heat shield inside of the rear wheel wells.
50. Remove the muffler and heat shield assembly from the vehicle.
51. Remove the retightened bolt and muffler mount. (Save for re-use)
52. Remove the snap ring and slide the spring and washer off of the mounting post.
53. Remove (30) fasteners securing the two halves of the heat shield.
54. Remove side sections of a heat shield.
55. Remove the front and back halves of a heat shield.
56. Re-install factory muffler hanging bracket to the mounting tabs on the Eurowise exhaust.
57. Re-assemble factory heat shield sections around Eurowise exhaust
58. Place the heat shield and x-pipe assembly back on the vehicle and adjust the fit.
59. Re-assemble remaining components by following steps 1 through 45 in reverse.

Eurowise-Audi-R8-V8-SuperSport-X-Pipe-Exhaust-System.pdf
1573677418-Eurowise-Audi-R8-V8-SuperSport-X-Pipe-Exhaust-System.pdf
IF YOU HAVE ANY QUESTIONS, COMMENTS, OR CONCERNS RELATED TO YOUR PRODUCT PLEASE CONTACT US!

CONTACT

• 440 SPRINGBROOK ROAD. CHARLOTTE, NC 28217 | 704-559-8100
• INFO@EUROWISE.COM | WWW.EUROWISE.COM | SHOP.EUROWISE.COM

References

• Specializing in European Service, Performance and Fabrication – Eurowise Performance
• Eurowise Audi, BMW, Volkswagen, Mercedes, & Porsche Service

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>