CORSAIR TX-M Series TX550M High Performance ATX Power Supply Instruction Manual

TX-M Series TX550M High-Performance ATX Power Supply
Instruction Manual

INTRODUCTION

Congratulations on the purchase of your new CORSAIR TX-M Series ATX Power Supply!
CORSAIR TX-M Series semi-modular power supplies deliver reliable 80 PLUS Gold efficient power to your system.
Please be sure to only use the screws, cables, and other hardware included in the box. Use of third-party hardware could result in damage to your power supply or your system and its components.

SAFETY AND PROTECTION

• Over-Voltage Protection (OVP)
  Over-voltage protection for the 12V, 5V, and 3.3V DC outputs is required to comply with the ATX specification. OVP shuts down the PSU in the event that the DC outputs exceed a set level, determined by the PSU manufacturer.

• Over-Current Protection (OCP)
  OCP is featured on the 3.3V, 5V, and 12V rails. OCP ensures that the output of the DC voltage rails remains within safe operating limits.

• Over-Temperature Protection (OTP)
  OTP ensures that the PSU will shut down when the internal temperature reaches a set point. This is usually a result of internal current overloading or a fan failure.

• Short-Circuit Protection (SCP)
  A short-circuit is defined as any output impedance of fewer than 0.1 ohms. Amongst other things, SCP ensures that the PSU shuts down should the 3.3V, 5V, and 12V rails short to any other rail, or to the ground. It also ensures that no damage should occur to the unit or your PC’s components in the event of a short.

TX550M INCLUDED HARDWARE AND SPECIFICATIONS

Dimensions: 140mm (L) x 150mm (W) x 86mm (H)
Package contents: Power supply, AC cable, DC cables, cable ties, mounting screws, safety leaflet

CORSAIR TX550M POWER TABLE

| | | MAX LOAD| MAX OUTPUT
---|---|---|---|---
MODEL| RPS0140| +3.3V| 25A| 120W
PART NO.| CP-9020228 / 75-004408| +5V| 20A
AC INPUT RATING| 100V a.c.-240V a.c.| +12V| 43A| 516W
INPUT CURRENT| 8A-4A| -12V| 0.8A| 9.6W
FREQUENCY| 47-63Hz| +5Vsb| 3A| 15W
TOTAL POWER: 550W

CORSAIR TX550M POWER SUPPLY EFFICIENCY

CORSAIR TX550M POWER SUPPLY FAN NOISE CURVE

TX650M INCLUDED HARDWARE AND SPECIFICATIONS

Dimensions: 140mm (L) x 150mm (W) x 86mm (H)
Package contents: Power supply, AC cable, DC cables, cable ties, mounting screws, safety leaflet

CORSAIR TX650M POWER TABLE

| | | MAX LOAD| MAX OUTPUT
---|---|---|---|---
MODEL| RPS0141| +3.3V| 25A| 130W
PART NO.| CP-9020229 / 75-004409| +5V| 25A
AC INPUT RATING| 100V a.c.-240V a.c.| +1W| 51A| 612W
INPUT CURRENT| 10A-5A| -1W| 0.8A| 9.6W
FREQUENCY| 47-63Hz| +5Vsb| 3A| 15W
TOTAL POWER: 650W

CORSAIR TX650M POWER SUPPLY EFFICIENCY

CORSAIR TX650M POWER SUPPLY FAN NOISE CURVE

TX750M INCLUDED HARDWARE AND SPECIFICATIONS

Dimensions: 140mm (L) x 150mm (W) x 86mm (H)
Package contents: Power supply, AC cable, DC cables, cable ties, mounting screws, safety leaflet

CORSAIR TX750M POWER TABLE

| | | MAX LOAD| MAX OUTPUT
---|---|---|---|---
MODEL| RPS0142| +3.3V| 25A| 130W
PART NO.| CP-9020230 / 75-004410| +5V| 25A
AC INPUT RATING| 100V a.c.-240V a.c.| +12V| 62A| 744W
INPUT CURRENT| 10A-5A| -12V| 0.8A| 9.6W
FREQUENCY| 47-63Hz| +5Vsb| 3A| 15W
TOTAL POWER: 750W

CORSAIR TX750M POWER SUPPLY EFFICIENCY

CORSAIR TX750M POWER SUPPLY FAN NOISE CURVE

CORSAIR TX-M SERIES CABLE INFORMATION

INSTALLING YOUR NEW TX-M SERIES POWER SUPPLY

Step 1: Removing Your Existing PSU
WARNING! To ensure proper function, only use the DC cables included with your new PSU, unless your old cables are genuine CORSAIR cables of the same type. Please confirm your existing cables’ type before using them!
If you are building a new system, skip to Step 2:

1. Disconnect the AC power cord from your wall outlet or UPS and from the existing power supply.
2. Disconnect all the power cables from your video card, motherboard, and all other peripherals.
3. Follow the directions in your chassis manual and uninstall your existing PSU.
4. Proceed to Step 2.

Step 2: Installing the New Power Supply

1. Make sure the power supply’s AC power cable is not connected.

2. Follow the directions in your chassis manual and install the power supply with the screws provided.

3. Connect the 24-pin (ATX) cable to the motherboard. Connect the 8-pin+12V (EPS12V) cable to the motherboard.
   a. If your motherboard has an eight-pin +12V socket, connect the eight-pin cable directly to your motherboard.
   b. If your motherboard has a four-pin socket, detach the four-pin from the eight-pin cable, and then plug this four-pin cable directly into your motherboard.
   c. Some motherboards will require a mix of 8+4 pins, use as many EPS12V cables as necessary, and do not mistake them for PCIe cables.

4. Connect the peripheral cables, PCI-Express cables, and SATA cables.
   a. Connect the SATA cables to your SATA SSD or hard drive’s power sockets.
   b. Connect the PCI-Express cables to the power sockets of your PCI-Express video cards if required.
   c. Connect the peripheral cables to any peripherals requiring a 4-pin connector.
   d. Make sure all the cables are tightly connected. Be sure to save any unused modular cables for future component additions.

5. Connect the AC power cord to the power supply and turn it on by pushing the switch to the ON position (marked with “I”).

WEB: corsair.com
PHONE: 888-222-4346
SUPPORT: support.corsair.com
BLOG: corsair.com/blog
FORUM: forum.corsair.com
YOUTUBE: youtube.com/corsairhowto

© 2021 CORSAIR MEMORY Inc. All rights reserved. CORSAIR and the sails logo are registered trademarks in the United States and/or other countries.
All other trademarks are the property of their respective owners. Product may vary slightly from those pictured. 49-002492 AA

References

• corsair.com
• Corsair Blog - Corsair Community
• Home - Corsair Community

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>