Ziel Home LTV117 Light Strips Instructions
- May 15, 2024
- Ziel Home
Table of Contents
Ziel Home LTV117 Light Strips
Instructions
- 22 Dynamic Modes
- 20 Static Colors
- Very Smooth Effects
- Speed Adjustable
- Brightness Adjustable
- Card Type RF Remote
- Ultra Slim Design
- Dynamic Demo Mode
- Easy Remote Pairing
- Direct Color Select
Turn On/Standby
Press this key to turn on unit or switch to standby mode. At power on, the
unit will automatically turn on and restore to the previous status.
Dynamic Mode Adjust
Switch to dynamic mode from static color, or switch between dynamic modes.
Dynamic speed Adjust
Adjust dynamic playing speed. Press SPEED+ to increase speed and press SPEED-
to decrease. Unit will switch to dynamic mode il press this key at static
color mode.
Static Color Adjust
Switch to static color mode from dynamic mode,or switch between static colors.
Direct Color Select
Shortcut key to static colors, When pressing the specific color key, the LED
will play the same static color. The direct colors are included in the
‘COLOR+’and ‘COLOR-‘ operation.
Functions
Brightness Adjust
Adjust static color brightness. Press BRIGHT+ to increase brightness and press
BRIGHT- to decrease. The unit will switch to static color mode if press this
key at dynamic mode.
Demo Mode
Press this key will switch to Demo mode. In demo mode, it plays 17 dynamic
modes in the loop, each mode repeated 3 times.
Installing
Power Supply
This unit accepts DC 5V to 24V power supply. The DC jack’s inner pole(or red
cable)is positive and the sleeve (or black cable) is negative. Also please
make sure the power supply voltage is the same as the LED load.
LED Output
This unit supports common anode connection LED products. The mark” ‘indicates
the common connection node.
The peak output current is 4 amperes and the maximum constant current is 2 amperes per channel. Please reduce the load if main unit is overheating
CAUTION
Do not short-circuit or overload the LED outputs, this may lead to
permanent damage
Operation
Using Remote Controller
- Please pull out the battery-insulated tape before using it. The RF wireless remote signal can pass through a barrier, so it’s not necessary to aim at the main unit when operating.
- Press the ‘ON/OFF ‘ and ‘MODE +’key together in 5 seconds after powering on. After this operation, the main unit will recognize any remote controller. To pair the main unit back to a specific remote, please repeat the pairing New Remote operation.
Switch Output Color Sequence
The controller’s default output signal sequence is Common-Green-Red-Blue. If
the LED application is indifferent cable sequence, the direct color keys will
not match the LED color In this case, the user can adjust the output signal
sequence with the following steps:
- Plug off the power of the main unit and plug-in after 5 seconds.
- Press the ‘ red ‘ and ‘BLUE ‘ color keys together in 5 seconds after powering on.
With this operation, the output sequence will switch between possible combinations. The sequence will be memorized and it won’t change before the next operation. For proper receiving remote signals, please do not install the main unit in closed metal parts.
Pairing New Remote
The remote and main unit are 1 to 1 paired as default Further, the main unit
can be paired to 3 remote controllers and each remote controller can be paired
to any main unit. Please do the following steps to pair the new remote
controller:
- Plug off the power of the main unit and plug-in after 5 seconds.
- Press’SPEED-‘ and’SPEED+’key together in 5 seconds. after power on.
After this operation, the main unit will recognize the new remote controller.
Free Remote Pairing Mode
In some specific cases, the main unit may need to be paired with any remote
controllers. Please do the following steps for free remote pairing mode:
- Plug off the power of the main unit and plug in after S seconds.
Specification
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Portable
RF Exposure Information
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>