ZIEL HOME LBT018 Light Strip for Bar Table Instructions
- May 15, 2024
- Ziel Home
Table of Contents
ZIEL HOME LBT018 Light Strip for Bar Table
Instructions
- 22 Dynamic Modes
- 20 Static Colors
- Very Smooth Effects
- Speed Adjustable
- Brightness Adjustable
- Card Type RF Remote
- Ultra Slim Design
- Dynamic Demo Mode
- Easy Remote Pairing
- Direct Color Select
Turn On/Standby
Press this key to turn on the unit or switch to standby mode. At power on, the
unit will automatically turn on and restore to the previous status.
Dynamic Mode Adjust
Switch to dynamic mode from static color, or switch between dynamic modes.
Dynamic speed Adjust
Adjust dynamic playing speed. Press SPEED+ to increase speed and press SPEED-
to decrease. The unit will switch to dynamic mode if presses this key at
static color mode.
Static Color Adjust
Switch to static color mode from dynamic mode,or switch between static colors.
Direct Color Select
Shortcut key to static colors, When pressing the specific color key.LED will
play the same static color. The direct colors are included in the ‘COLOR+’and
‘COLOR- operation.
Functions
Brightness Adjust
Adjust static color brightness. Press BRIGHT+ to increase brightness and press
BRIGHT- to decrease. The unit will switch to static color mode if this key in
dynamic mode.
Demo Mode
Press this key will switch to Demo mode. In demo mode, it plays 17 dynamic
modes in the loop. each mode is repeated 3 times.
Installing
Power Supply
This unit accepts DC 5V to 24V power supply. The DC jack’s inner pole(or red
cable)is positive and the sleeve (or black cable) is negative. Also please
make sure the power supply voltage is the same as the LED load.
LED Output
This unit supports common anode connection LED products. The mark” ”indicates
the common connection node. The peak output current is 4 amperes and the
maximum constant current is 2 amperes per channel. Please reduce the load if
the main unit is overheating
CAUTION
Do not short-circuit or overload the LED output, this may lead to permanent
damage.
Operation
Using Remote Controller
- Please pull out the battery-insulated tape before using it. The RF wireless remote signal can pass through a barrier, so it’s not necessary to aim at the main unit when operating.
- Press the ‘ON/OFF ‘ and ‘MODE +’key together in 5 seconds after powering on. After this operation, the main unit will recognize any remote controller. To pair the main unit back to a specific remote, please repeat the pairing New Remote operation.
Switch Output Color Sequence
The controller’s default output signal sequence is Common-Green-Red-Blue.If
the LED application is in a different cable sequence, the direct color keys
will not match the LED color. In this case, the user can adjust the output
signal sequence with the following steps:
- Plug off the power of the main unit and plug-in after 5 seconds.
- Press the ‘ red ‘ and ‘BLUE ‘ color keys together in 5 seconds after powering on.
With this operation, the output sequence will switch between possible
combinations. The sequence will be memorized and it won’t change before the
next same operation. For proper receiving remote signal, please do not install
the
the main unit in closed metal parts.
Pairing New Remote
The remote and main unit is 1to 1 paired as default Further, the main unit can
be paired to 3 remote controllers and each remote controller can be paired to
any main unit. Please do the following steps to pair the new remote
controller:
- Plug off the power of the main unit and plug it in after 5 seconds.
- Press’SPEED-‘ and’SPEED+’key together in 5 seconds. after power on. After this operation, the main unit will recognize the new remote controller.
Free Remote Pairing Mode
In some specific cases; the main unit may need to be paired to any remote
controllers. Please do the following steps for free remote pairing mode:
- Plug off the power of the main unit and plug in after S seconds.
Specification
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Not applicable
RF Exposure Considerations
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment can be used as portable without any
restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>