Ziel Home BBK361 Human Baby Sensing Light Strip Instructions
- June 12, 2024
- Ziel Home
Table of Contents
Ziel Home BBK361 Human Baby Sensing Light Strip
Product Information
The Human Baby Sensing Light Strip is a device designed to provide illumination and sensory stimulation for babies. It is equipped with a built- in sensor that detects the presence of a baby and automatically activates the light strip. This product complies with part 15 of the FCC Rules and has been evaluated to meet general RF exposure requirements.
FCC Statement
This device is in compliance with FCC regulations. It operates under the
following conditions:
- This device does not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
The Human Baby Sensing Light Strip can be used in portable exposure conditions without any restrictions.
ISED Statement
This device has also been evaluated to meet general RF exposure requirements
set by the Innovation, Science and Economic Development Canada (ISED). The
device can be safely installed and operated with a minimum distance of 0mm
between the radiator and your body.
Product Usage Instructions
- Ensure that the Human Baby Sensing Light Strip is securely installed in a suitable location within your baby’s room.
- Connect the power adapter to the designated port on the light strip and plug it into a power outlet.
- The light strip will automatically activate when it senses the presence of a baby in the room. It will provide gentle illumination to create a soothing environment.
- To turn off the light strip, either remove the baby from the room or manually switch off the power using the designated button or switch.
- Make sure to keep the light strip clean and free from any obstructions to ensure optimal performance.
Always refer to the user manual for additional information or troubleshooting steps.
Button Operation Instruction
- MODE +/MODE -: Switch to dynamic mode from static color, or switch between dynamic modes.
- Mode switch+/Previous mode
- Mode switch-/Next mode
- DEMO: Color cycle display mode. In demo mode, it plays dynamic modes in the loop.
- SPEED +/SPEED-: Adjust the flashing speed(Six-speed mode)
- COLOR +/COLOR-: Switch color (switch between static color)
- BRIGHT +/BRIGHT-: Adjust the brightness(Six brightness modes) (Both dynamic and static can be used)
In addition, there are 7 static colors, making up a total of 25 color modes.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution:
Any changes or modifications to this device not explicitly approved by the
manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
ISED Statement
This device complies with Industry Canada license‐exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
The digital apparatus complies with Canadian CAN ICES‐3 (B)/NMB‐3(B).
- This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
- This equipment complies with Canada’s radiation exposure limits set forth for an uncontrolled environment.
RF Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The
device can be used installed and operated with a minimum distance of 0 mm
between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>