VIVO MOUNT-VC90-10 Large TV Ceiling Mount with Extension Pole Instruction Manual
- May 15, 2024
- Vivo
Table of Contents
Large TV Ceiling Mount
with 10ft Pole
SKU: MOUNT-VC90-10
Instruction Manual
Assembly Video & Product Info
www.vivo-us.com/products/mount-vc90-10
CAUTION
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please contact our product support team at
309-278-5303 or help@vivo-us.com for further assistance. Check carefully to
make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that
is not explicitly specified in this manual. Do not exceed weight capacity. We
cannot be liable for damage or injury caused by improper mounting, incorrect
assembly or inappropriate use.
| WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
---|---
| DO NOT EXCEED WEIGHT CAPACITY
FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY.
| WARNING: DO NOT INSTALL INTO DRYWALL ALONE
VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO MOUNT. We include mounting
for brick
and concrete walls. If unsure, please contact us at vivo-us.com, email at
help@vivo-us.com, or call us at 309-278-5303.
We’re Here for You
Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer
immediate assistance with rapid response times. If any parts are received
damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
| Give us a Call:
309-278-5303| AVG. RESOLUTION TIME (within office hrs): 5M 4S
---|---|---
| Chat Us:
www.vivo-us.com| AVG. RESOLUTION TIME (within office
hrs): < 15 M
| Email Us:
help@vivo-us.com| AVG. RESPONSE TIME (within office
hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
Package Contents
Included Hardware & Tools
Tools Needed:
Weight Capacity:
ASSEMBLY STEPS
STEP 1a
Option A | Wood Joist Installation
Use a stud finder to locate your desired mount position, then hold Mounting
Template (G) against ceiling and mark the hole positions using a pencil.
Note: When mounting to a flat ceiling, it is recommended the mounting plate is
parallel with tv orientation if possible.
Drill 2.2” (55mm) deep holes using a 3/16” (4.5mm) drill bit.
Attach the Mounting Pole (A) to the ceiling using ST6.3x55mm Screws (W-A) and
M6 Washers (W-C). Tighten using a drill with either a Phillips end bit or a
10mm Socket.
[STEP 1a – Cont’d ] Adjust the angle of Pole (A) so that it is vertical, then tighten the nuts and bolts on the Mounting Plate using the 6mm Allen Wrench (T-B) and Wrench (T-A).
STEP 1b
Option B | Concrete Installation
Hold Mounting Template (G) up to your desired mounting location and mark hole
positions using a marker.
Note: When mounting to a flat ceiling, it is recommended the mounting
plate is parallel with tv orientation if possible.
Drill 1.8” (45mm) deep holes using a 1/2” (12mm) drill bit.
Remove the Washers and Nust from Concrete Anchors (W-B). Insert Concrete Anchors into the pre-drilled holes. Then secure Mounting Pole (A) to the ceiling using the previously removed Washers and Nuts. Tighten the nuts on Concrete Anchors () using a torque wrench with a 14mm socket set to 40ft-lbs (54 N-m).
Adjust the angle of Pole (A) so that it is vertical, then tighten the nuts and bolts on the Mounting Plate using the 6mm Allen Wrench (T-B) and Wrench (T-A).
STEP 2
Slide Mounting Adapter (F) on to Lower Pole (C). Route cables through all of
the Poles (A,B,C)
Connect Mounting Pole (A) and Middle Pole (B) together using M8x60mm Screws
(S-B), M8 Nuts (S-C), and 5mm Allen Wrench (T-B). Slide Lower Pole (C) into
Middle Pole (B) and place at your desired height. Secure using M8x55 Screws
(S-A), M8 Nuts (S-C), and 5mm Allen Wrench (T-B).
PLEASE NOTE: Parts are NOT shown to scale.
STEP 3
Use Wrench (T-A) to remove the single Lower Nut from VESA Support (E)
Slide VESA Support (E) onto the front of Mounting Adapter (F) and reinstall the previously removed Lower Nut using Wrench (T-A).
Remove the Collar Screws on VESA Brackets (C) using a Phillips screwdriver and set aside.
STEP 4
Install the VESA Brackets (D) onto the back of your screen using appropriate
combination of Screws (M-A through M-D), M8 Washers (M-E), and Spacers (M-F,
M-G) for your VESA pattern.
Tighten screws using a Phillips screwdriver. Example combinations are shown
below. 
STEP 5
Hang your TV with VESA Brackets (D) onto the VESA Support Bar (E).
STEP 6
Secure VESA Brackets (D) in place using the previously removed Collar Screws
and a Phillips screwdriver.
Make tilt and angle adjustment as desired, then tighten the nuts on the side
of Mounting Adapter (F). Lock the rotation in place by tightening the
preinstalled screw on the back of Mounting Adapter using a 5mm Allen Wrench
(T-B).
LAST UPDATED: 10/26/23
REV1
v1.0
Need Help? Get In Touch
Monday-Friday from 7:00am-7:00pm CST
| |
---|---|---
help@vivo-us.com| www.vivo-us.com
Chat live with an agent!| 309-278-5303
FOR MORE GREAT VIVO PRODUCTS,
CHECK OUT OUR WEBSITE AT: WWW.VIVO-US.COM
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>