V I V O MOUNT-VC90-5 Large TV Ceiling Mount with Extension Pole Instruction Manual
- May 15, 2024
- V I V O
Table of Contents
Instruction Manual
SKU: MOUNT-VC90-5 Large TV Ceiling Mount
with 5ft Pole
MOUNT-VC90-5 Large TV Ceiling Mount with Extension Pole
Assembly Video & Product Info
www.vivo-us.com/products/mount-vc90-5
CAUTION!
| WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
---|---
| DO NOT EXCEED WEIGHT CAPACITY FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY.
| WARNING: DO NOT INSTALL INTO DRYWALL ALONE
VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO MOUNT. We include mounting
for brick and concrete walls. If unsure, please contact us at vivo-us.com,
email at help@vivo-us.com, or call us at
309-278-5303.
We’re Here for You
Open Monday – Friday 7:00am – 7:00pm CS T,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
| Give us a Call: 309-278-5303| AVG. RESOLUTION TIME (within office hrs): <
15 M
---|---|---
| Chat Us: www.vivo-us.com| AVG. RESOLUTION TIME
(within office hrs): 5M 4S
| Email Us: help@vivo-us.com| AVG. RESPONSE TIME
(within office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
Package Contents
Included Hardware & Tools
Tools Needed: Weight Capacity:
ASSEMBLY STEPS
Option A | Wood Joist Installation
Use a stud finder to locate your desired mount position, then hold Mounting
Template (F) against ceiling and mark the hole positions using a pencil .
Note: When mounting to a flat ceiling, it is recommended the mounting
plate is parallel with tv orientation if possible.
Drill 2.2” (55mm) deep holes using a 3/16” (4.5mm) drill bit. Attach the
Mounting Pole (A) to the ceiling using ST6.3x55mm Screws (W-A) and M6 Washers
(W-C). Tighten using a drill with either a Phillips end bit or a 10mm Socket.
[STEP 1a – Cont’d ]
Adjust the angle of Pole (A) so that it is vertical, then tighten the nuts and
bolts on the Mounting Plate using the 5mm Allen Wrench (T-B) and Wrench (T-A).
STEP 1b
Option B | Concrete Installation
Hold Mounting Template (F) up to your desired mounting location and mark hole
positions using a marker.
Note: When mounting to a flat ceiling, it is recommended the mounting
plate is parallel with tv orientation if possible. Drill 1.8” (45mm) deep
holes using a 1/2” (12mm) drill bit. [STEP 1b – Cont’d ]
Remove the Washers and Nust from Concrete Anchors (W-B). Insert Concrete
Anchors into the pre-drilled holes. Then secure Mounting Pole (A) to the
ceiling using the previously removed Washers and Nuts. Tighten the nuts on
Concrete Anchors (W-B) using a torque wrench with a 14mm socket set to 40ft-
lbs (54 N-m). Adjust the angle of Pole (A) so that it is vertical, then
tighten the nuts and bolts on the Mounting Plate using the 5mm Allen Wrench
(T-B) and Wrench (T-A). STEP 2
Slide Mounting Adapter (E) onto Lower Pole (B) and rest at the bottom of the
Pole. Route cables through both Poles (A,B), then slide Lower Pole into
Mounting Pole at your desired height. Secure using M8x55mm Screws (S-A), M8
Nuts (S-B), and 5mm Allen Wrench (T-B). STEP 3
Use Wrench (T-A) to remove the single Lower Nut from VESA Support (D) Slide
VESA Support (D) onto the front of Mounting Adapter (E) and reinstall the
previously removed Lower Nut using Wrench (T-A). Remove the Collar Screws on
VESA Brackets (C) using a Phillips screwdriver and set aside. STEP 4
Install the VESA Brackets (C) onto the back of your screen using appropriate
combination of Screws (M-A through M-D), M8 Washers (M-E), and Spacers (M-F,
M-G) for your VESA pattern.
Tighten screws using a Phillips screwdriver. Example combinations are shown
below. STEP 5
Hang your TV with VESA Brackets (C) onto the VESA Support Bar (D). STEP 6
Secure VESA Brackets (C) in place using the previously removed Collar Screws
and a Phillips screwdriver.
Make tilt and angle adjustment as desired, then tighten the nuts on the side
of Mounting Adapter (E). Lock the rotation in place by tightening the
preinstalled screw on the back of Mounting Adapter using a 5mm Allen Wrench
(T-B).
LAST UPDATED: 10/23/23
REV1 v1.0
Monday-Friday from 7:00am-7:00pm CST
Need Help? Get In Touch
help@vivo-us.com
www.vivo-us.com
Chat live with an agent!
309-278-5303 FOR MORE GREAT VIVO PRODUCTS,
CHECK OUT OUR WEBSITE AT: WWW.VIVO-US.COM
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Large TV Ceiling Mount with Extension Pole – VIVO - desk solutions, screen mounting, and more