POWER FIST 8986739 3 Outlet Steel Retractable Extension Cord Reel Instruction Manual

8986739 3 Outlet Steel Retractable Extension Cord Reel
Instruction Manual

Please read and understand all instructions before use. Retain this manual for future reference.

SPECIFICATIONS

INTRODUCTION

The retractable extension cord reel allows you to easily extend power to your projects. The reel can swivel 180° and has an extension cord with 3 power outlets. Mount the reel indoors on the wall or ceiling to reduce clutter in the workshop or garage.

SAFETY

WARNING! Read and understand all instructions before using this tool.
The operator must follow basic precautions to reduce the risk of personal injury and/or damage to the equipment.

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A notice is an alert that there is a possibility of property damage, injury, or death if certain instructions are not followed.

DANGER!| This notice indicates an immediate and specific hazard that will result in severe personal injury or death if the proper precautions are not taken.
---|---
WARNING!| This notice indicates a specific hazard or unsafe practice that could result in a serious injury if the proper precautions are not taken.
CAUTION!| This notice indicates a potentially hazardous situation that may result in minor or moderate injury if proper practices are not taken.
NOTICE!| This notice indicates that a specific hazard or unsafe practice will result in equipment or property damage, but not personal injury.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well-lit, and free of distractions. Place lights so you are not working in a shadow.
2. Keep anyone not wearing the appropriate safety equipment away from the work area.
3. Store unused tools properly in a dry, safe and secure location to prevent rust, damage or misuse.
4. Do not install or use in the presence of flammable gases, dust, or liquids.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the Canadian Standards Association (CSA) or American National Standards Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT
WARNING! Wear personal protective equipment approved by the Canadian Standards Association (CSA) or American National Standards Institute (ANSI).

1. Always wear impact safety goggles that provide front and side protection for the eyes. Eye protection equipment should comply with CSA Z94.3-07 or ANSI Z87.1 standards based on the type of work performed.
2. Wear protective clothing designed for the work environment and tools.

PERSONAL PRECAUTIONS
Control the tool, personal movement, and the work environment to avoid personal injury or damage to the tool.

1. Do not operate any tool when tired or under the influence of drugs, alcohol, or medications.
2. Avoid wearing clothes or jewelry that can become entangled with the moving parts of a tool. Keep long hair covered or bound.

SPECIFIC SAFETY

WARNING! DO NOT let comfort or familiarity with the product (gained from repeated use) replace strict adherence to the tool safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury.
DANGER! DO NOT open the reel case. Do not attempt to disassemble the main spring assembly. A spring that is under high tension can cause serious personal injury or death when released. Has the tool been repaired by a certified technician? 

1. Use the correct tool for the job. This tool was designed for a specific function. Do not modify or alter this tool or use it for an unintended purpose.

2. Do not use the tool if any parts are damaged broken or misplaced. Repair or replace the parts.
   a. A qualified technician is required to replace or repair the reel’s internal mechanism.

3. Secure the retractable reel by using mounting hardware and fasteners to maintain stability under vibration.

4. Ensure the reel is properly installed before plugging it into a wall outlet or connecting a tool.

5. Do not exceed the reel’s rated amp capacity. The collective amp draw of three tools plugged into the reel’s triple outlet must be less than the amount listed in the  Specifications. Exceeding the rated capacity could result in loss of power and overheating.

6. Exercise care when handling the retractable reel during normal operation.
   The reel has a rotating drum powered by a spring under tension. Do not allow the cord to retract without restraining the recoil speed. Never let go of the cord when rewinding.

7. Prevent damage to the power cord by observing the following:
   a. Never carry the tool by the power cord
   b. Keep the cord away from heat, oil, sharp edges, or moving parts.
   c. Always pull on the extension cord. Never pull on the attachment.
   d. Do not abruptly jerk on the extension cord, as this can damage the cord or the locking mechanism

8. Unplug the cord reel and disconnect any tools if the reel ceases to wind or unwind. The power cord may be caught and damaged in the mechanism, creating an electric shock hazard.

9. Do not allow people, mobile equipment or vehicles to pass over unprotected power cords. Position power cords away from high traffic areas.

ELECTRICAL SAFETY

WARNING! Do not touch or handle a live tool with any part of your body that is wet or damp. Wet skin reduces resistance to electrical current, increasing the danger of a serious or fatal shock.
WARNING! To reduce the risk of electric shock, be certain that the plug is connected to a properly grounded receptacle.

1. Shut the power off and disconnect the retractable extension cord reel from the power supply (if possible) before making any adjustments, changing accessories, cleaning,  servicing, or when storing. Such preventive safety measures reduce the risk of starting the tool accidentally.
2. Do not alter any parts of the tool or accessories. All parts and accessories are designed with built-in safety features that may be compromised if altered.
3. Protect yourself against electric shocks when working on electrical equipment. Avoid body contact with grounded surfaces. There is an increased chance of electrical shock if your body is grounded.
4. Do not expose the retractable extension cord reel to rain, snow, frost, or any other damp or wet conditions. Water entering a tool will increase the risk of electric shock.
5. Do not disconnect the power cord in place of using the power switch. This will prevent an accidental start-up when the power cord is plugged into the power supply.
6. In the event of a power failure, turn off or unplug the machine as soon as the power is interrupted. The possibility of accidental injury could occur if the power returns and the unit is not switched off.
7. Make certain the power source conforms to the requirements of your equipment (see Specifications).
8. This tool is only for use on 120 V (single phase) and is equipped with a three-prong grounded power supply cord and plug. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tool should electronically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user.
   a. Never remove the grounding prong or modify the plug in any way, as this will render the tool unsafe.
   b. Do not use any adapter plugs.

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace the missing part before operating. Failure to do so could result in a malfunction and personal injury.
Remove the parts and accessories from the packaging and inspect for damage.
Contents:

• Retractable Extension Cord Reel

IDENTIFICATION KEY

ASSEMBLY & INSTALLATION

Four 7/16 in. screws or M12 bolts and matching washers are required to mount the reel. The hardware must be purchased separately.

1. Select an indoor wall or ceiling location within four feet of a grounded electrical outlet. The mounting location must have solid construction.
   Drywall will not hold the reel in place.
   a. Install the reel no higher than 15 feet above the floor.
   b. Check that the power at the outlet conforms to the rating for the reel (see Specifications).

2. Locate a wall or ceiling beam (use a stud finder, if needed), and using the mounting bracket as a template, mark the holes so they are centered on the beam.

3. Screw the cement or wood screws into the marks, leaving the screw heads slightly raised above the surface.

4. Slide the mounting bracket onto the screws. Finish tightening the screws to hold the reel in place.

5. Adjust the cord stopper to a suitable position when required.

6. Loosen the screw holding both halves of the stopper enough to slide the stopper. Pull out the extension cord until enough is hanging out. Slide the stopper to the desired location, then tighten the screw to lock it in place.
   Pull the extension cord and allow it to retract to the stopper.

OPERATIONS

WARNING! Do not let go of the extension cord while retracting or extending. The cord may whip around during retraction and cause an injury by striking a bystander. The tool’s mechanism may also be damaged.

1. Slowly pull out the amount of the extension cord required for the task. A click will be heard every half rotation of the internal drum.
   • Pull on the extension cord, not on any tool plugged into the cord.

2. Latch the extension cord in place by allowing it to slowly retract back into the reel case after a click. The extension cord will feel slack when latched..

3. Plug the tools into the extension cord end. Ensure that all tools that will operate at once will draw less than the maximum amperage (see specifications).
   • Do not switch ON more than one tool a time. A tool may draw more amps than its rating when powering up.

4. Plug the reel’s power supply cord into a power outlet.

5. Unplug the reel’s power supply cord when the task is complete.

6. Disconnect and store all tools connected to the extension cord.

7. Pull the extension cord out of the reel case until you hear a click, then slowly allow the line to retract until the stopper reaches the reel case. Repeat this step if the cord latches again and allow the extension cord to retract a little faster.

CARE & MAINTENANCE

DANGER! DO NOT open the reel case. Do not attempt to disassemble the main spring assembly. A spring that is under high tension can cause serious personal injury or death when released. Has the tool been repaired by a certified technician?

1. Maintain the tool with care. A tool in good condition is efficient, easier to control, and will have fewer problems.
2. Inspect the tool components periodically. Repair or replace damaged or worn components.. Only use identical replacement parts when servicing.
3. Maintain the tool’s labels and nameplates. These carry important information. If unreadable or missing, contact Princess Auto Ltd. for replacements.

WARNING! Only qualified service personnel should repair the tool. An improperly repaired tool may present a hazard to the user and/or others.

DISPOSAL

Recycle a tool damaged beyond repair at the appropriate facility.
Contact your local municipality for a list of disposal facilities or by-laws for electronic devices, batteries, oil or other toxic liquids.

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not function properly or parts are missing. If unable to do so, have a qualified technician service the tool.

spring.
No electrical power at the output end of an extension cord.| 1. Power outlet is not
functioning.
2. Amperage draw has
tripped the circuit
breaker.
3. Extension cord or power
supply cord is damaged.| 1. Check the outlet’s breaker and reset it if needed. If the outlet is still dead, have an electrician replace it.
2. Follow steps in Operation –
Circuit Breaker to reset.
3. Replace the reel or have a certified technician replace the damaged component.
The cable does not retract
at all.| Spring lost tension or is broken.| Have a qualified technician replace the spring canister.
Circuit breakers trip or
fuses blow repeatedly.| 1. Equipment does not conform to the reel’s electrical rating.
1. Discontinue the use of equipment with the reel.
2. Wires have shorted.| 1. Discontinue the use of equipment with the reel.
2. Have a qualified technician replace wires.
The reel retracts too fast.| The reel is not tensioned properly.| Decrease spring tension. Refer to
Adjusting Spring Tension.

PARTS BREAKDOWN

PARTS LIST

www.princessauto.com / 1-800-665-8685

References

• princessauto.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>