V I V O STAND-LAP1F Aluminum Laptop Floor Stand Instruction Manual
- May 15, 2024
- V I V O
Table of Contents
V I V O STAND-LAP1F Aluminum Laptop Floor Stand
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
NOTE: SOME PARTS INCLUDED MAY NOT BE USED DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
TIPOVER WARNING
- SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF THE STAND
- USE TIP-OVER RESTRAINT OR ANCHOR STAND TO WALL
- THE USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
PACKAGE CONTENTS
NOTE
- SOME PARTS INCLUDED MAY NOT BE USED
- DO NOT EXCEED WEIGHT CAPACITY.
- Failure to do so may result in serious injury.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT
TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF THE STAND
- USE TIP-OVER RESTRAINT OR ANCHOR STAND TO WALL
- THE USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
ASSEMBLY STEPS
STEP 1
Assemble the Left Foot (B) to the Base (A) using M6x10mm Bolts (S-A). Tighten
with the 4mm Allen Wrench (T-A).
STEP 2
Insert the threaded side of Pole (C) into the base assembly, making sure
the slot is facing towards the back. Secure the pole using the M10x25mm Bolt
(S-B) and the 6mm Allen Wrench (T-A).
STEP 2 (Continued)
Tighten the rear set screw using the 4mm Allen Wrench (T-A).
STEP 3
Slide the Arm (D) onto Pole (C), loosening the thumbscrew first if needed.
Press the Pole Cap (E) into the top of Pole (C). Tighten thumbscrew at desired
height for Arm (D).
STEP 4
OPTION A
Laptop TrayRemove the pre-installed bolt and white plastic spacer from the
Laptop Hinge (F) using the 5mm Allen Wrench (T-A). Insert the hinge swivel
joint into the top of the Arm (D), making sure the tabs in the black plastic
bushing fit into the slots in the hole. Secure using the previously removed
spacer and bolt with the 5mm Allen Wrench (T-A). Slide the Laptop Tray (I)
into the Laptop Hinge (F) until the latch engages. Adjust the tilt joint if
necessary using the 5mm Allen Wrench (T-A), then pull out on the sides of the
tray and place the laptop computer into the tray.
STEP 4 (Continued)
OPTION B: Tablet Holder
Remove the bolt and white plastic spacer from the Tablet Hinge (G) using the
5mm Allen Wrench (TA). Insert the hinge swivel joint into the top of the Arm
(D), making sure the tabs in the black plastic
bushing fit into the slots in the hole. Secure using the previously removed
spacer and bolt with the Allen Wrench (T-A). Install the Tablet Holder (H)
using the M5x16mm Bolt (S-C) with the 4mm Allen Wrench (T-A). Adjust the tilt
joint if necessary using the 4mm Allen Wrench (T-A), then pull out the holder
clips and place the tablet into the Tablet Holder (H).
Adjust as Desired
Love your new VIVO setup and want to share?
Tag us in your photo! vivo_us
Open Monday – Friday 7:00 am – 7:00 pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product. FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Aluminum Laptop Floor Stand – VIVO - desk solutions, screen mounting, and more