DYNOJET PC6-18011 Power Commander 6 Installation Guide
- June 4, 2024
- Dynojet
Table of Contents
POWER COMMANDER 6
Installation Guide for PC6-18011
Model Coverage: 2011-2013 KTM 690R Enduro
Installation Guide
PARTS LIST
1 POWER COMMANDER 6
1 INSTALLATION GUIDE
1 USB CABLE
2 DYNOJET DECALS| 2 POWER COMMANDER DECALS
2 VELCRO STRIPS
1 ALCOHOL SWAB
3 ZIP TIES
---|---
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION. THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
Map (Input 1 or 2) The PC6 has the ability to hold 2 different base maps.
You can switch on the fl y between these two base maps when you hook up a
switch to the MAP inputs. You can use any open/close type switch. The polarity
of the wires is not important.
Shifter (Input 1 or 2) Used for clutch-less full throttle upshifts.
Insert the wires from the Dynojet quick shifter into either Input 1 or Input
2. The polarity of the wires is not important. Set to Input 2 by default.
Speed If your application has a speed sensor then you can tap into the
signal side of the sensor and run a wire into this input. This will allow you
to calculate gear position in the Control Center Software. Once gear position
is set up you can alter your map based on gear position and setup gear-
dependent kill times when using a quick shifter.
Analog This input is for a 0-5v signal such as engine temp, boost, etc.
Once this input is established you can alter your fuel curve based on this
input in the Power Core software.
Launch You can connect a wire to either Input 1 or Input 2 and then the
other end to a switch. This switch when engaged (continuity) will only allow
the RPM to be raised to a certain limit (set in the software). When released,
you will have full RPM.
WIRE CONNECTIONS
To input wires into the PC6 fi rst remove the rubber plug on the backside of
the unit and loosen the screw for the corresponding input. Using a 22-24 gauge
wire, strip about 10mm from its end. Push the wire into the hole of the PC6
until it stops and then tightens the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make inserting them
easier.
2 2011-2013 KTM 690R ENDURO
INSTALLING THE POWER COMMANDER 6
-
Remove the seat.
-
Remove the left and right side radiator shrouds.
-
Remove both of the screws (one on each side) that secure the air box to the frame.
-
Loosen the clamp that secures the air box to the throttle body.
-
Lift upward on the rear of the air box. This should cause the rubber intake duct slip off of the throttle body.
-
Position the PC6 module above the battery while routing the wiring harness forward along the right side of the air box and towards the throttle body.
-
Secure the PC6 ground wire with the small ring lug to the negative (-) terminal of the bike’s battery.
-
While lifting the rear of the air box to access the throttle body, unplug the stock wiring harness from the Fuel Injector located at the top of the throttle body.
-
Plug the PC6 wiring harness in-line of the Fuel Injector and the stock wiring harness.
-
Locate and unplug the stock wiring harness from the Throttle Position Sensor.
WARNING – This TPS is located on the right side of the throttle body and has a BLUE connector. There is an identical connector on the left side of the throttle body. Be sure to connect to the one on the right side. -
Plug the PC6 wiring harness in-line with the TPS and the stock wiring harness.
4 2011-2013 KTM 690R ENDURO
-
Locate and unplug the stock Crank Position Sensor connectors.
This is a WHITE 2-pin connector pair. It can be found near the large BROWN connectors for the bike’s main wiring harness. -
Plug the PC6 wiring harness in-line of the stock CPS connectors.
-
Using the supplied Velcro, secure the PC6 module to the top of the battery.
Clean both surfaces with the supplied alcohol swab prior to applying the Velcro. -
Use the remaining zip ties to secure the PC6 wiring harness. Keep it free and clear from any hot or moving parts.
-
Slide the rubber intake duct back over the throttle body and tighten the clamp.
-
Reinstall the two screws that secure the air box to the frame.
-
Reinstall the radiator shrouds and the seat.
Download the latest map fi les from our website at dynojet.com/tunes.
2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081
–800-992-4993
DYNOJET.COM
© 2011-2022 DYNOJET RESEARCH ALL RIGHTS RESERVED
Documents / Resources
|
DYNOJET PC6-18011 Power Commander
6
[pdf] Installation Guide
PC6-18011 Power Commander 6, PC6-18011, Power Commander 6, Power Commander,
Commander 6, 2011-2013 KTM 690R Enduro
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>