A3305S Anker Power Conf User Manual

Anker Power Conf
User Manual

A3305S Anker Power Cone

Anker Power Conf S500
USER MANUAL

At a Glance

1 Volume down button
2 Mute button
3 Phone call button
4 Volume up button
5 Power button| 6 Play button
7 Link button
8 Bluetooth button
9 USB-C charging port
---|---

Charging

• Fully dry off the USB-C charging port before charging.
• Fully charge the speakerphone before the first use to extend the lifespan.
• Use a certified USB-C charging cable and charger to prevent any damage.

Powering On / Off

Press and hold the power button for three seconds to power on or off.

• The PowerConf speakerphone will automatically power on once connected to your PC by using the USB-C cable.
• The PowerConf speakerphone will automatically power off after 30 minutes in the case of no signal input or output.
• To check the battery level, press the power button again when powered on.

Connecting

There are 3 ways that you can connect the PowerConf speakerphone to your devices.
Option A: Connect to PC (Bluetooth Dongle)

1. Plug the provided Bluetooth dongle into a USB port on your PC. PowerConf S500 will be ready to use when it is powered on.
2. You might need to manually set PowerConf S500 as the audio device for your PC system or conference software.
   • macOS
   System Preferences > Sound > Sound Effects / Output / Input
   • Windows
   Right-click on the sound icon > Open Sound settings > Choose your output device / Choose your input device
   • Software (Zoom, Skype or more)
   Settings > Audio > Speaker / Microphone

Option B: Connect to PC (USB-C Cable)
Connect PowerConf S500 to a PC using the provided USB-C cable. It will be ready to use when it’s powered on.

Option C: Connect to Smartphone or Tablet (Bluetooth)

1. When powered on, PowerConf S500 will automatically enter Bluetooth pairing mode. Alternatively, press the Bluetooth button to enter Bluetooth pairing mode.
2. Select “Anker PowerConf S500” on your smartphone’s Bluetooth list to connect.

| Press| Enter Bluetooth pairing mode
---|---|---
| Flashing blue| Pairing
| Steady blue| Connected

• Each time you power on PowerConf S500, it will automatically connect with the last successfully connected device if available. If not, press the Bluetooth button to enter Bluetooth pairing mode.
• This speakerphone can pair up with two mobile devices via Bluetooth at a time. To pair with another Bluetooth device, press the Bluetooth button to re-enter Bluetooth pairing mode.
• When the speakerphone is connected to two devices via USB and Bluetooth at the same time, press and hold the play button for two seconds to switch between Bluetooth and USB modes.
• To disconnect the Bluetooth from one device, press the Bluetooth button again on the device that’s currently active.
• If connection via the Bluetooth dongle fails, plug it into a USB port on your PC and then press the PC mute button four times. The light on the dongle will flash quickly. This indicates that the dongle has been  reset with all pairing history cleared. The dongle will then connect with the speakerphone automatically.

Using Your PowerConf

| Press and hold for 3 seconds| Power on / off
---|---|---
Press (when powered on)| Check the battery level
| Press| Enter Bluetooth pairing mode or disconnect
Bluetooth
| Press| Answer / End a call
Press and hold for 2 seconds| Reject a call or activate Siri
| Press or press and hold| Volume up / down
| Press| Mute or restore the microphone
| Press| Play / Pause / Resume music
Press twice| Switch between USB and Bluetooth modes
when both are available
Press and hold for 2 seconds| Activate Siri or other voice assistant software
| Press| Link with another PowerConf S500

LED Light Bar

Lights up red then flashes (battery level <10%)
Flashes blue| Incoming call
Lights up cyan (Standard mode)| Sound direction detected
Lights up purple (Broadcasting mode)
Lights up blue then turns off| Adjust volume
Turns red| Muted
Lights up cyan| Enter linking mode

Anker Work App

Download the Anker Work app to enhance your experience.

• Check product information
• Read user manual
• Check battery level
• Check for the latest firmware updates
• Adjust volume
• Set auto-power off
• Manage devices
• Turn LED light bar off
• Set voice pickup modes

There are two voice pickup modes you can choose from in the Anker Work app.

• Standard mode: Pick up all sounds from the near end.
• Broadcasting mode: Restore and deliver original sounds by turning the speaker off. You will not hear the far end anymore when in this mode. (You are strongly suggested to use this mode via USB connection).

Linking Mode
Linking mode is available only when you connect one PowerConf S500 with your PC using the USB-C cable. It is not available when connected via Bluetooth.

1. Connect one PowerConf S500 with your PC using the provided USB-C cable.
2. Power on another PowerConf S500, then press the link button on both PowerConf S500 speakerphones simultaneously to enter linking mode.

| Press| Enter linking mode
---|---|---
| Flashing cyan| Connecting
| Steady cyan| Connected

• This mode is not available when both PowerConf S500 speakerphones are connected via a USB cable.
• The recommended distance between the two PowerConf S500 speakerphones is about 3 m.
• To exit linking mode, press and hold the link button for 2 seconds simultaneously on both PowerConf S500 speakerphones.

Specifications

Specifications are subject to change without notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>