V I V O STAND-V038F Dual Monitor Desk Stand Instruction Manual

: May 15, 2024
: V I V O

Table of Contents

We’re Here for You
Package Contents
Included Hardware & Tools
ASSEMBLY STEPS
ADJUSTMENTS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

V I V O STAND-V038F Dual Monitor Desk Stand Instruction Manual

CAUTION!

If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product support team at 309-278-5303 or help@vivo-us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

Symbol
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

DO NOT EXCEED WEIGHT CAPACITY
FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY.

We’re Here for You

Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

Give us a Call: 309-278-5303
AVG. RESOLUTION TIME (within office hrs): 5M 4S

Chat Us: www.vivo-us.com
AVG. RESOLUTION TIME (within office hrs): < 15 M

Email Us: help@vivo-us.com
AVG. RESPONSE TIME (within office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr

Package Contents

A (x1) Pole
B (x1) Base
C (x1) Arm
D (x2) VESA Plate
E (x1) Pole Cap
F (x1) Cover
G (x4) Arm Cable Clips
H (x1) Pole Cable Clip

Included Hardware & Tools

S-A (x2) M6 Cap Nut
M-A (x8) M4x12mm Thumbscrew
M-B (x8) M4x30mm Screw
M-C (x8) Spacer
T-A (x1) 3mm Allen Wrench
T-B (x1) 6mm Allen Wrench

Tools Needed:

Phillips Screwdriver

Weight Capacity:

Per Arm

ASSEMBLY STEPS

STEP 1

Slide Cover (F) and Pole Cable Clips (H) over Pole (A), then thread Pole into Base (B). Press Pole Cap (E) into the top of Pole. Lock Cover into place by tightening Set Screws using 3mm Allen Wrench (T-A).

STEP 2

Slide Arm (C) onto Pole (A) and secure at desired height using 6mm Allen Wrench (T-B).
Attach Arm Cable Clips (G) onto each arm segment on Arm (C).
Assembly Instruction

STEP 3

Install VESA Plates (D) onto your monitors using M4x12mm Thumbscrews (M-A) or M4x30mm Screws (M-B) and Spacers (M-C) if needed. Lightly tighten with a Phillips screwdriver.
Assembly Instruction

STEP 4

Slide your monitors with VESA Plate (D) onto Arm (C). Secure the VESA Plates (D) to the Arm using M6 Cap Nuts (S-A).
Assembly Instruction

STEP 5

Route cables through Arm and Pole Cable Clips (G,H).
Assembly Instruction

WARNING

Do not extend the arms past the base shown below.
Assembly Instruction

ADJUSTMENTS

Adjust the tilt joint resistance using 6mm Allen Wrench (T-B).
Assembly Instruction

Remove the M6 Cap Nuts (S-A) and adjust the VESA height adjustment screws using 3mm Allen Wrench (T-A).
Reinstall the M6 Cap Nuts.
Assembly Instruction