FRONT RUNNER PBAC006 Pro Bed Rack Recovery and Accessory Mount

Product Information

• Specifications:
  • Product Name: Front Runner Pro Bed Rack Recovery and Accessory Mount
  • Model Number: PBAC006
  • Manufacturer: Front Runner
  • Compatibility: Pro Bed Rack

Product Usage Instructions

• Getting Started
  • Before installation, ensure you have all the necessary components listed in the manual. Refer to Page 2 for a detailed list.
• Fit and Secure
  • Follow these steps to install the Front Runner Pro Bed Rack Recovery and Accessory Mount:
  • Slide four M8 x 16 Hex Bolts into the top and bottom side profiles of your Pro Bed Rack.
  • Place the Mounting Plates onto the Hex Bolts and loosely fasten the Nyloc Nuts.
  • If mounting MAXTRAX or similar devices, align the Mounting Brackets with the corresponding mounting holes and secure them using appropriate hardware.
  • If mounting a Universal Side Mount for a Pro Water Tank or Rotopax, follow the specific instructions provided in the manual.
  • Tighten all Nyloc Nuts and add the Plastic Nut Caps for a secure fit.
• Finish
  • Congratulations on completing the installation! Take a moment to appreciate your work.
• Additional Accessories
  • Explore other vehicle and rack accessories available from Front Runner to enhance your setup.
• Frequently Asked Questions (FAQ):
  • Q: What should I do if I encounter difficulties during installation?
  • A: If you face any challenges during installation, please contact Front Runner for assistance to ensure proper product setup and avoid any potential damages.
  • Q: Can I use this product with other brands of recovery boards or water tanks?
  • A: The Front Runner Pro Bed Rack Recovery and Accessory Mount is designed for compatibility with specific devices such as MAXTRAX,  TRED GT, TRED PRO, and Rotopax. For other brands, please check compatibility before installation.

INTRODUCTION

READ ME!

• Thank you for purchasing a Front Runner Pro Bed Rack Recovery and Accessory Mount.
• Before you start, take a moment to familiarize yourself with the Fitting Instructions and the included components.
• Refer to Page 2 for a list of all the components, quantities and tools required.

IMPORTANT WARNING!

• ALL FRONT-RUNNER PRODUCTS MUST BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE.
• IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH.
• YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT-RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS BEFORE USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE.
• THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT-RUNNER PRODUCT PRIOR TO INSTALLATION OR USE.
• IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
• NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
• Please call us if you have any questions about the installation of this product.

IN THE BOX

1. 2 X Mounting Plate
2. 8 X M8 x 16mm Hex Bolt
3. 8 X M8 Plastic Nut Cap
4. 8 X M8 Nyloc Nut

TOOLS NEEDED

OVERVIEW

FIT AND SECURE

• Slide four M8 x 16 Hex Bolts (Item 2) into the top side profile of your Pro Bed Rack and four M8 x 16 Hex Bolts (Item 2) into the bottom side profiles of your Pro Bed Rack as seen in Fig 2.1.
• Place the Mounting Plates (Item 1) onto the M8 x 16 Hex Bolts (Item 2) and loosely fasten the Nylock Nuts (Item 4).

MAXTRAX / TRED GT / TRED PRO Fitment

• Space the Mounting Brackets (Item 1) to align with the MAXTRAX / TRED GT / TRED PRO mounting holes.
• For MAXTRAX use either PBAC009 (Pro Bed Rack Recovery Device Mounting Hardware) or REQU120 (MAXTRAX Mounting Pin Set) to fasten the recovery board to the mounting plates.
• For TRED GT/TRED PRO use PBAC009 (Pro Bed Rack Recovery Device Mounting Hardware).
• Once the Mounting Brackets are spaced correctly, tighten the M8 Nyloc Nuts (Item 4) and add the Plastic Nut Caps (Item 3) to the M8 Nyloc Nuts (Item 4).

Universal Side Mount for Pro Water Tank Fitment

• Space the Mounting Brackets (Item 1) to align with the VACC099 (Universal Side Mount for Pro Water Tank) mounting holes.
• Use the mounting hardware supplied with VACC099 to fasten. Tighten the M8 Nyloc Nuts (Item 4) and add the Plastic Nut Caps (Item 3) to the M8 Nyloc Nuts (Item 4).

Rotopax Fitment

• Mount the Rotopax Brackets to the Mounting Brackets (Item 1) using the hardware supplied with the Rotopax.
• Space the Mounting Brackets (Item 1) to align with the Rotopax mounting holes. Tighten the M8 Nyloc Nuts (Item 4) and add the Plastic Nut Caps (Item 3) to the M8 Nyloc Nuts (Item 4).
• Note the orientation of the mounting plates for the Rotopax fitment.

FINISH

• Congratulations! You did it. Take a step back and admire your work!

Be sure to tag us. We love to see our gear in action!

• FrontRunnerOutfitters

• BornToRoam

• Share your adventures on:

PBAC006_REV_A01 © 2023 FRONT RUNNER VEHICLE OUTFITTERS CHECK ONLINE FOR THE LATEST FITMENT GUIDE WWW.FRONTRUNNEROUTFITTERS.COM.

References

• FRONTRUNNEROUTFITTERS.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>