Newell Air Artha Max XL LED Light Instructions
- June 17, 2024
- Newell
Table of Contents
Newell Air Artha Max XL LED Light
SAFETY INSTRUCTIONS
Before using the product, please read the following instruction manual carefully and keep it for future reference. When transferring the product to a third party, it is advisable to include the instructions.
-
The lamp is a precision device. Do not drop, hit, crush or expose to any shock.
-
The unit is not dustproof or waterproof. Store in a dry, cool and ventilated place.
Do not expose to water or other sources of moisture. -
Do not use near flammable materials and solvents.
-
Do not use the lamp too close to objects. Do not cover the ventilation holes. Do not insert metal parts into the lamp. Do not touch the electrical parts with conductive materials.
-
The lamp can operate in a temperature range of 0°C – 40°C.
-
The lamp will heat up slightly, but it is normal.
-
Do not stare directly at the LED panel that is turned on, it may cause eye damage.
-
Do not use the LED outside in direct sunlight for a long time.
-
Disconnect the power supply for storage or transportation. Do not lift the camera while holding the lamp handle.
-
Allow the unit to cool down before placing it in the package.
-
For use by adults.
-
If you notice smoke or a strange smell coming from the device, immediately disconnect the power. Do not disassemble. Disassembling the unit will void the warranty. If there are problems with the lamp, bring it to an authorized service center.
Maintenance
Use a dry and soft cloth to clean the unit. Do not clean with water. A
little neutral detergent on the cloth to remove stubborn dirt. Do not use
strong detergents such as thinner, benzine or alcohol as they may damage the
protective coatings.
PRODUCT DESCRIPTION
- Light panel
- Angle adjustment knob
- Fixing bracket
- Bracket fixing knob
- V-Mount battery holder
- Battery removal button
- Control panel
- Remote control
POWER ON/OFF
-
Use battery power
Insert a V-mount battery into the battery compartment of the photography light in the correct direction. Flip the power switch to the T’. The LCD screen display lights up and the photography light will turn on. You can use either one v-mount battery or two. The lamp will work the same way. -
Use external adapter for power supply
Use an external adapter to supply power. Connect the 15V 4A adapter to the power supply. Flip the power switch to the ‘Il’. The LCD screen display lights up, and the light will turn on normally. -
Power off
Turn the power switch to ‘O’. The LCD screen display goes off and the light turns off.
FUNCTION ADJUSTMENT SETTINGS
Control panel
- Power switch
- Power socket
- Display
- Color temperature button
- Channel group button
- Mode button
- Adjustment knob
- DMX interface – input
- DMX interface – output
Brightness adjustment
After starting up by turning the adjustment knob, change the brightness to the
desired. Turn the adjustment knob clockwise to increase the brightness. Turn
the adjustment knob counterclockwise to decrease the brightness.
Color temperature adjustment
After starting up, press the “color temperature adjustment button”. On the
display, the color temperature value will flash once. By turning the knob
adjustment, change the color temperature to the desired temperature.Once the
color temperature adjustment is complete, you can operate other activities or
wait 5 seconds to exit the color temperature adjustment.
Remote control mode
When the lamp is turned on, press the channel group button and the remote
control channel displayed on the LCD will flash. At this time, you can set the
remote control channel with the dial. Press the channel group button of the
LCD display again. At this time, you can set the remote control group with the
dial.
If the remote control channel on the product and the remote control coincide,
the remote control can be used to remotely control the product. Once the
setting is complete, you can operate other activities or wait 5 seconds to
exit the color temperature adjustment.
DMX mode
When the lamp is turned on, press the mode button to switch to DMX mode. When
the remote control channel on the LCD switches to the DMX channel, press the
channel group button. The DMX channel on the display will flash. At this
point, you can set the DMX channel using the dial. Since the brightness and
color temperature of the photo lamp each occupy one channel of the DMX
console, the DMX channel on the photo lamp will be displayed as 1, 3, 5, 7, 9.
When the DMX channel is 1, channel 1 on the DMX console corresponds to the
brightness, channel 2 corresponds to the color temperature, and so on. Once
you enter DMX mode, you cannot use the remote control and color temperature
buttons.
If you want to exit DMX mode, press the mode button again. The channel shown
on the display will be switched to the remote control channel and group. This
indicates a successful exit.
REMOTE CONTROL
Remote control functions
- LDC Display
- CH / GRP button
- ON / OFF button
- – button
- + button
- SET button
- Battery cover
Remote control on / off
- Remove the battery cover and insert two AAA batteries into the battery compartment according to the positive and negative polarity markings in the battery compartment.
- Press and hold the ON/OFF button on the controller for 3 seconds to turn on / turn off the remote control. If no operation is performed on the remote control for 15 seconds, the backlight of the remote control will turn off.
Remote control channel setting
After the remote control is turned on, press CH and the channel value on the
display flashes once, press the plus and minus buttons to set the number of
channels of the remote control.
Turning on / off the light
After the remote control is turned on and the remote control channel is the
same as the video light channel setting. Press the ON/OFF button on the remote
control to turn on / off the light.
Brightness and color temperature
When the remote control channel is the same as the light channel setting,
press the + or – buttons on the remote control to adjust the brightness of the
camera light. Press the SET button, the color temperature value flashes once.
At this time, press the + or – buttons on the remote control to adjust the
color temperature value of light. After the color temperature adjustment is
completed, press the SET button again. If there is no operation within 5
seconds, the remote control will exit the color temperature adiustment.
DMX Control
-
DMX Controller connection
Connect the DMX controller to the power supply, and connect the data cable to the DMX input port of the lamp. After turning on the lamp, press the DMX mode button and turn the adjustment knob of the control knob to set the DMX channel to the target value. The lamp can be controlled by adjusting the corresponding channel with the DMX controller. The lamp must occupy two channels of the controller, the first adjusts the brightness and the second adjusts the color temperature. -
Connecting several devices via DMX
Connect the lights via DMX ports (output-input) with each other, and then connect to the controller.
After the connection is made, the DMX controller can normally control all the connected lights.
According to the change of the channel, lights can be controlled simultaneously or separately.
APP OPERATION GUIDE
- Use your mobile phone to scan the unified download QR code corresponding to the picture above or search for RHD Light” app through Google Play (Android) or App Store (Apple iOS) to download.
- Open the app, you need to agree to all the necessary permissions and function switches. If the Bluetooth is not turned on, it will prompt to turn on the Bluetooth to scan and connect the device, select “OK to turn on the Bluetooth” or manually turn on the mobile phone Bluetooth (ISO needs to be manually turned on).
- The product will run.
- As shown in (Pic. 1), click “+” on the app to enter the “device scanning” interface to start scanning devices. After waiting for about a few seconds, the “bound device picture and device name” as shown in (Pic 2) will be displayed. Click to display the (Pic 3) interface. Click picture 3 interface: the status: the figure 4 interface will appear. Click the top right of (Pic 4) interface (Gr:A CH:1) to select group channel that is the same as the product lamp. By selecting different tabs on the top of the app, you can control and adjust the product in the corresponding interface under the app. Click “connected” in Picture 3 to slide to the left and picture 5 will appear. Click “delete” in Picture 5 to prompt o delete the bound device. Note: click help on each interface of the app to display specific operation guide of the app.
PRODUCT SIZE
Unit: mm Tolerance: + 1.0mm L=722 W=690 H=14.5
SPECIFICATION
WASTE MANAGEMENT
The crossed-out trashcan symbol means that waste electrical and electronic
equipment,batteries and packagings must not be placed with other household
waste. They must be handed over to a separate waste collection system.
WARRANTY
40 WARRANTY
Newell
Newell products are covered by a 40-month manufacturer’s warranty.
*The manufacturer reserves the right to change the information contained in this manual without prior notice.
RECE
Made in China, In China hergestellt, Hecho en China, Fabbricato in Cina,
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>