V I V O STAND-V001O Mechanical Arm Single Monitor Desk Mount Instruction Manual
- June 17, 2024
- V I V O
Table of Contents
Mechanical Arm Single Monitor
Desk Mount
Instruction Manual
SKU: STAND-
V001O
STAND-V001O Mechanical Arm Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.
https://vivo-us.com/products/stand-v001o
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
help@vivo-us.com
www.vivo-us.com
Chat live with an agent!
309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about
the safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT
TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF
TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1 – Clamp Installation
Remove Plastic Cover (C1) from Base (C). Adjust the hand bolt completely down
on Lower Clamp (D).
0.4”-1.90” (10-50mm) DESKTOPS
Install Upper Clamp (E) to Base (C) using M6x8mm Screws (S-A) and 5mm Allen
Wrench (T-A).
Reinstall Plastic Cover (C1) onto Base (C). Attach Lower Clamp (D) to the top two holes on Upper Clamp (E) using M6x10mm Screws (S-B) and 4mm Allen Wrench (T-B). Secure clamp assembly to the desktop.
1.8”-3.1” (45-80mm) DESKTOPS
Install Upper Clamp (E) to Base (C) using M6x8mm Screws (S-A) and
5mm Allen Wrench (T-A). Reinstall Plastic Cover (C1) onto Base
(C). Attach Lower Clamp (D) to the bottom two holes on Upper Clamp
(E) using M6x10mm Screws (S-B) and 4mm Allen Wrench (S-B). Secure
clamp assembly to the desktop. STEP 1 – Grommet
If desktop does not have a preexisting grommet hole, use a ⅜” (10mm) drill
bit to create one by drilling completely through the desktop. 
Disassemble Lower Clamp (D) using the Phillips end
on 5mm Allen Wrench (T-A) and separate Hand Bolt (D1). Place Grommet
Plate (F) on Hand Bold (D1) and secure Base (C) to the desktop.
STEP 2
Place Lower Arm (A) onto Base (C), then place Upper Arm (B) onto
Lower Arm (A). Tighten set screws using the flathead end on 4mm Allen
Wrench (T-B).
STEP 3
STEP 4
Install two Screws (M-A or M-B) and M5 Washers (M-C) using the Phillips end of
5mm Allen Wrench (T-A) to the top VESA holes on the monitor leaving at least
3mm of clearance between the screw and monitor. Slide the monitor onto VESA
Plate (G) making sure the screws sit within the slots.
Tighten the top two screws and install the
remaining Screws (M-A or M-B) and 5mm Washers (M-E) using the
Phillips end of 5mm Allen Wrench (T-A). 
Cable Management
Remove plastic covers from Arms (A,B) using Phillips screwdriver end of 5mm Allen Wrench (T-A). Run cables from monitor through bottom of Arms (A,B), then reattach plastic covers.
Adjust as Desired
Use 5mm Allen Wrench (T-A) to adjust tilt. 
Tension Adjustment
While holding the arm in the horizontal position, adjust the gas spring
tension using the 5mm Allen Wrench (T-A).
CAUTION:
To avoid damage to the monitor or mount, always ensure the arm is in a
horizontal position before making adjustments. An additional person may be
required to assist in some cases. If the arm drops, turn the adjustment screw
clockwise until it stays in a horizontal position.
If the arm rises, turn the adjustment screw counter-clockwise until it stays
in a horizontal position
CAUTION:
Do not over tighten screws.
WARNING:
Monitor must be installed on mount before making tension adjustments to the
gas spring arm.
CAUTION:
DO NOT rotate monitor past rear edge of desk to avoid an unstable situation may cause tipping.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
309-278-5303| AVG. RESOLUTION TIME
(within office hrs): 5M 4S
---|---
www.vivo-us.com
Chat live with an agent!| AVG. RESOLUTION TIME (within office hrs): <
15 M
help@vivo-us.com| AVG. RESPONSE TIME (within
office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT
OUR WEBSITE AT : www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>