MONDAINE GGM.D083 Neo Ronda Startech Swiss Watch Instruction Manual

/ INSTRUCTION MANUAL /
Neo
Ronda startech
Movement Cal. 5030.D

Description of the display and control buttons

Setting the time

1.  * Pull out the crown to position Ill (the watch stops).
2.  Turn the crown until you reach the correct time 8:45.
3.  * Push the crown back into position I.
   Please note:

• In order to set the time to the exact second, 1 must be pulled out when the second hand is in position « 0 ». Once the hour and minute hands have been set, 3 must be pushed back into position | at the exact second.

Setting the date (quick mode)

1. Pull out the crown to position II (the watch continues to run).
2.  Tun the crown until the correct date [ 1 ] appears.
3.  Push the crown back into position I.
   Please note:
   During the date changing phase between approx.
   9 PM and midnight the date must be set fo the date of the following day.

Setting the date/time following a battery change

Example:
— Date / time on the watch: 17 / 1:25AM
— Present date / time: 4 8:30 PM

1. Pull out the crown to position Il (the watch continues to run).

2.  Tun the crown until yesterday’s date appears [ 3 ].

3. • Pull out the crown to position III (the watch stops).

4.  Tun the crown until the correct date 4 appears.

5. ** Continue to turn the crown until the correct time 8:30 PM appears.

6.  Push the crown back intoposition I.
   Please note:

• To set your watch to the exact second, please refer to the chapter entitled «setting the time».
  ** Please observe the AM/PM watch rhythm.

Chronograph

Basic function (Start/Stop/Reset)

Example:

1. Start: Press push-button A.
2. Stop: to stop the timing, press push-button A once more and read the chronograph hands: 1h / 20min / 38 sec.
3.  Zero positioning:
   Press push-button B.
   (The chronograph hands will be reset to their zero positions.)

Accumulated timing

Example:

1. Start(start timing)

2.  Stop:(e.g. 15 min 5 sec following 1 )

3.   Restart: (timing is resumed)

4. *Stop: (e.g._5 min 12 sec following 3 )
   = 20 min 17 sec
   (The accumulated measured time is shown)

5. Reset
   The chronograph hands are returned to their Zero positions.
   Please note:

• Following 4 , the accumulation of the timing can be continued by pressing push-button A (Restart / Stop, Restart / Stop, …).

Intermediate or interval timing

Example:

1. Start: (start timing)

2.  Display interval:
   e.g. 20 minutes 17 seconds (timing te continues in the background)

3.  Making up the measured time: (the chronograph hands are quickly advanced to the ongoing measured time).

4.  Stop: (Final time is displayed.)

5.  Reset
   The chronograph hands are returned fo their zero position

Please note:

• Following 3 , further intervals or intermediates can be displayed by pressing push- button B (display interval / make up measuredtime, …).

Adjusting the chronograph

hands to zero position

Example:
One or several chronograph hands are not in their correct zero positions and have to be adjusted (e.g. following a battery change).

1. Pull out the crown to position Ill (all chronograph hands are in their correct or incorrect zero position.)

2. Keep push-buttons A and B depressed simultaneously for at least 2 seconds (the second counter hand rotates by 360° — corrective mode is activated.)
   

3.  Returning the crown to position |
   Termination of the chronograph hands adjustment (can be carried out at any time).

Registered models. All rights reserved and defended by the manufacturer and the Swiss Government authorities. All wrist watches are Swiss made by Watch Ltd, Etzelstrasse 27, 8808 Pfaffikon, Switzerland T +41 (0)58 666 88 00 | info@mondaine.ch www.mondaine.ch

References

• Mondaine Schweizer Bahnhofsuhren

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>