MONDAINE Neo Ronda Startech Watch Instruction Manual
- June 11, 2024
- MONDAINE
Table of Contents
/ INSTRUCTION MANUAL /
Neo
Ronda startech
Movement Cal. 5030.D
Description of the display and control buttons
Setting the time
- Pull out the crown to position IIl (the watch stops).
- Turn the crown until you reach the correct time 8:45.
- Push the crown back into position I.
Please note :
- In order to set the time to the exact second, 1 must be pulled out when the second hand is in position « Q ».
Once the hour and minute hands have been set, 3 must be pushed back into position | at the exact second.
Setting the date (quick mode)
- Pull out the crown to position II (the watch continues to run).
- Turn the crown until the correct date 1 appears.
- Push the crown back into position I.
Please note:
During the date changing phase between approx.
9 PM and midnight the date must be set to the date of the following day.
Setting the date/time following a battery change
Example:
— Date / time on the watch: 17 / 1:25AM
— Present date / time: 4 / 8:30 PM
-
Pull out the crown to position Il (the watch continues to run).
-
Tun the crown until yesterday’s date appears [ 3 ].
-
Pull out the crown to position III (the watch stops).
-
Tun the crown until the correct date [ 4 ] appears.
-
-
- Continue to turn the crown until the correct time 8:30 PM appears.
-
-
Push the crown back intoposition I.
Please note:
- To set your watch to the exact second, please refer to the chapter entitled «setting the timex.
** Please observe the AM/PM watch rhythm.
Chronograph
Basic function (Start/Stop/Reset)
Example:
-
Start: Press push-button A.
-
Stop: to stop the timing, press push-button A
once more and read the chronograph hands:
1h / 20min / 38 sec. -
Zero positioning:
Press push-button B.
(The chronograph hands will be reset to their zeto positions.)
Chronograph
Accumulated timing
Example:
-
Stort(start timing]
-
Stop:e.g. 15 min 5 sec following 1 )
-
Restart: (timing is resumed)
-
Stop: (e.g. 5 min 12 sec following 3 )
= 20 min 17 sec
(The accumulated measured time is shown) -
Reset:
The chronograph hands are returned to their zero positions.
Please note:
- Following 4 , the accumulation of the timing can be continued by pressing push-button A (Restart / Stop, Restart / Stop, …}.
Chronograph
Intermediate or interval timing
Example: –
-
Start: (start timing)
-
Display interval:
e.g. 20 minutes 17 seconds (timing to continues in the background) -
Making up the measured time:
(the chronograph hands are quickly advanced to the ongoing measured time). -
Stop: (Final time is displayed.)
-
Resets
The chronograph hands are returned to their Zero position
Please note:
- Following 3 further intervals or intermediates can be displayed by pressing pushbutton B (display interval / make up measured time, …).
Adjusting the chronograph
hands to zero position
Example:
One or several chronograph hands are not in their correct zero positions and
have to be adjusted (e.g. following a battery change).
-
Pull out the crown to position Ill (all chronograph hands are in their correct or incorrect zero position.)
-
Keep push-buttons A and B depressed simultaneously for at least 2 seconds (the second counter hand rotates by 360° →corrective mode is activated.)
-
Returning the crown to position | Termination of the chronograph hands adjustment (can be carried out at any time).
Since 2020, Mondaine Group (including all brands) is one of the first watch companies worldwide to be comprehensively CO2 neutral for scope 1,2,3 of the GHG protocol. Reduce, Reuse, Recycle.
WARNING
KEEP THE BATTERY OUT OF REACH OF CHILDREN The battery can cause serious
injuries if swallowed or placed inside any part of the body. Seek medical
attention immediately.
GGM.D083
ED. 04/24
Registered models. All rights reserved and defended by the manufacturer and the Swiss Government authorities. All wrist watches are Swiss made by M ondaine Watch Ltd, Etzelstrasse 27, 8808 Pfaffikon, Switzerland T +41 (0)58 666 88 00 | info@mondaine.ch www.mondaine.ch