Honeywell HD73P IR Dome Camera Instruction Manual

Honeywell HD73P IR Dome Camera

Product Information

Specifications

• Product Name: IR Dome Camera
• Model: HD70(73)P/PX series
• Part Number: 800-07007-A
• Manufacturer: Honeywell
• Minimum Illumination:
  • F2.0, 50 IRE, AGC Max: 0.3 LUX (Color, B/W)
  • F1.4, 50 IRE, AGC Max: 0.3 LUX (Color)
  • IR LED ON: 0 LUX
• Resolution: Ultra High Resolution (600 TVL)
• Features:
  • Adaptive IR Technology
  • 1/3 High Sensitivity CCD
  • SBLC (Super Back Light Compensation)
  • DNR (Digital Noise Reduction)
  • Privacy zone selectable
  • Mirror (Horizontal)
  • Flickerless On/Off

Product Usage Instructions

Installation

1. Stick the guide pattern on the wall or ceiling and mark the mounting holes.
2. Drill four holes according to the guide pattern, then insert anchors into the drilled holes.
3. Draw out power/video wires and make the connections.
4. Attach the camera base to the ceiling or wall using the supplied four screws.
5. Aim and focus by turning and moving the 3-axis camera bracket by hand.
6. Align the dome cover over the base.
7. Secure the dome cover to the base using the supplied L-wrench.

Name and Functions

Camera Layout:

• Tilt rotation: Adjusting the vertical angle.
• Pan rotation: Adjusting the horizontal angle.
• Horizontal rotation: Adjusting the horizontal position of the screen.

Use the joystick to navigate through the menus.

Main Menu – General
Press the MENU button to access the SETUP menu. Select each sub-menu by using the UP, DOWN, LEFT, and RIGHT buttons. Press the MENU(SET) button to select.

• DOWN: Move down
• UP: Move up
• LEFT: Move left
• RIGHT: Move right
• MENU(SET): Press the joystick in its straight position
• Service Monitor Connector: Use the service monitor connector to set camera angle & focus when installing.

Lens Menu
Press the MENU button to access the SETUP menu. Select LENS using the UP or DOWN button. You can change between ESC and DC using the LEFT or RIGHT button. Select ESC and press the MENU button to display LENS ESC.

FAQ

• How do I dispose of this product?
  This product should be disposed of, at the end of its useful life, as per applicable local laws, regulations, and procedures.

• What safety standards does this product conform to?
  This product conforms to the requirements of standards EN 55022 for emissions, EN 50130-4 for immunity, and EN 60950 for Electrical Equipment safety.

READ AND KEEP THIS OPERATION MANUAL

Warnings
Installation and servicing should be performed only by qualified and experienced personnel to conform to all local codes and to maintain your warranty.

WARNING!
12V DC models require the use of CSA Certified/UL Listed Class 2 power adapters to ensure compliance with electrical safety standards.

WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product (applicable in the European Union and other European countries with separate collection systems). This product should be disposed of, at the end of its useful life, as per applicable local laws, regulations, and procedures.

FCC Compliance Statement

Information to the User: This equipment has been tested and found to comply with the limits for a Class A digital device. Under Part 15 of the FCC Rules, these limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Caution
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Manufacturer’s Declaration of Conformance
The manufacturer declares that the equipment supplied with this guide is compliant with the essential protection requirements of the EMC Directive 2004/108/EC and the General Product Safety Directive GPSD 2001/95/EC, conforming to the requirements of standards EN 55022 for emissions, EN 50130-4 for immunity, and EN 60950 for Electrical Equipment safety.

WARNING:
This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.

USER INFORMATION

CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION!
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

• The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
• The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating instructions in the literature accompanying the appliance.

Thank you for purchasing this COLOR VIDEO CAMERA.
Before using this camera, please read this operation manual carefully to obtain the best result and keep this manual for future reference.

SAFETY INSTRUCTIONS

• Read Instructions
  Read all of the safety and operating instructions before using the product.

• Retain Instructions
  Save these instructions for later use.

• Cleaning
  Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

• Power source
  This product should be operated only from a 12V DC power source as indicated on the marking label.

PRECAUTIONS

• Do not install the camera in extreme temperature conditions.
• Do not disassemble the camera.
• Do not drop the camera or subject them to physical shocks.
• Never keep the camera face to strong light directly.

NOTE
When this camera is installed near wireless communication devices that emit a strong electromagnetic field, irregularity such as noise on the monitor may appear.

FEATURES

Adaptive IR Technology
“Adaptive IR” technology dramatically eliminates the white-out effect and saturation on close objects, producing a clear and recognizable image regardless of viewing condition or location of objects.

1/3” High Sensitivity CCD

HD70P(PX)

Min Illumination (F2.0, 50 IRE, AGC Max)

• 0.3 LUX (Color, B/W)
• 0 LUX (IR LED ON)

User-friendly menus

• Ultra High Resolution (600 TVL)
• SBLC (Super Back Light Compensation)
• DNR (Digital Noise Reduction)
• Privacy zone selectable
• Mirror (Horizontal)
• Flickerless On/Off

Breather vent

HD73P(PX)
Min Illumination (F1.4, 50 IRE, AGC Max)

• 0.3 LUX (Color)
• 0 LUX (IR LED ON)

SUPPLIED ACCESSORIES

INSTALLATION

1. Stick the guide pattern on the wall or ceiling and mark the mounting holes.
2. Drill four holes according to the guide pattern, then insert anchors into the drilled holes.
3. Draw out power/video wires and make the connections.
4. Attach the camera base to the ceiling or wall using the supplied four screws.
5. Aim and focus by turning and moving the 3-axis camera bracket by hand.
6. Align the dome cover over the base.
7. Secure the dome cover to the base using the supplied L-wrench.

Ceiling

NAME AND FUNCTIONS

Fixed Lens Type
HD70P(PX) shown

Camera Layout

1. Tilt rotation: Adjusting the vertical angle.
2. Pan rotation: Adjusting the horizontal angle.
3. Horizontal rotation: Adjusting the horizontal position of the screen.

Vari-focal Lens Type
HD73P(PX) shown

Camera Layout

1. Tilt rotation: Adjusting the vertical angle.
2. Pan rotation: Adjusting the horizontal angle.
3. Horizontal rotation: Adjusting the horizontal position of the screen.
4. Focus handle: Focus (Far or Near)
5. Zoom handle: Zoom (Tele or Wide)

CONNECTIONS

1. Connecting to Monitor and Power
   • Connect the video-out jack to the video-in jack of the monitor.
   • Connect the power adapter to the power input connecter.
   • Use 12V DC power source.
   • Use the power rated at least 400 mA (12V DC)

OPERATING CAMERA

LENS

| ESC| BRIGHTNESS| 0~5
---|---|---|---

DC

| DC LEVEL| 0~5

SHUTTER

| 1/60(1/50),1/120(1/100),1/250,1/500,1/700,1/1K,1/1600,1/2500

1/5K,1/7K,1/10K,1/30K,1/60K,1/120K

IR MODE:1/60(1/50)

WHITE BAL

| ATW|
MANUAL| RED| 0~160
BLUE| 0~160
PUSH|
AGC| ON| LEVEL| 0~20 (IR MODE:FIXED)
OFF|

DAY / NIGHT

| IRED| MODE| WIDE, SMART
CHANGE LEVEL| LOW, MIDDLE, HIGH
COLOR|  |
B/W| BURST| ON/OFF

IMAGE ADJ

| SBLC| OFF, LOW, MIDDLE, HIGH
DNR| OFF, LOW, MIDDLE, HIGH
SHARPNESS| LEVEL| 0~20
MIRROR| OFF, ON|

MOTION (NTSC/PAL)

| AREA| 1~4
DISPLAY| OFF, ON
SENSITIVITY| 1~24
TOP| 8~126 / 10~146
BOTTOM| 8~126 / 11~149
LEFT| 4~191 / 8~191
RIGHT| 4~191 / 9~192
INITIAL| OFF , ON
RETURN|  | |

Use the joystick to navigate through the menus.

• a. DOWN: Move down

• b. UP: Move up

• c. LEFT: Move left

• d. RIGHT: Move right

• e. MENU(SET):
  Press the joystick in its straight position.

• f. Sevice Monitor Connecter:
  Use the service monitor connector to set the camera angle & focus when installing.

MAIN MENU

MAIN MENU – GENERAL

Press the MENU button to access the SETUP menu.

• Select each sub-menu by using the button.
• Press the MENU(SET) button to select.

If the OSD MENU is changed then INITIAL will be OFF (EXCEPT: LENS)

LENS
Press the MENU button to access the SETUP menu.

LENS ESC (HD73P(PX))

• Select LENS using the UP or DOWN button. You can change between ESC and DC using the LEFT or RIGHT button.
• Select ESC and press the MENU button to display LENS ESC.

1. BRIGHTNESS
   

   • Select BRIGHTNESS using the UP or DOWN button.
   • You can adjust between 0 to 5 using the LEFT or RIGHT button.

LENS DC (HD73P(PX))
Select DC and press the MENU button to have LENS DC activated.

1. DC LEVEL (Adjusts brightness of the image.)
   • Select DC LEVEL using the UP or DOWN button. You can adjust between 0 to 20 levels using the LEFT or RIGHT button.
2. FLK (FLICKER LESS)
   • Select FLK using the UP or DOWN button. You can select between ON / OFF using the LEFT or RIGHT button.
   • OFF: You will be allowed to adjust the shutter speed.
3. SHUTTER (Adjusts the shutter speed of the lens.)
   • IR LED Mode : 1/60(1/50)
   • COLOR, B/W Mode:
     Select SHUTTER using the UP or DOWN button. You can adjust from 1/60(1/50), 1/120(1/100), 1/250, 1/500, 1/700, 1/1K, 1/1600, 1/2500, 1/5K, 1/7K, 1/10K, 1/30K, 1/60K, 1/120K(sec) level using the LEFT or RIGHT button.

WHITE BAL (White Balance)
Select WHITE BAL using the UP or DOWN button. You can select from ATW, MANUAL, or PUSH using the LEFT or RIGHT button.

1. ATW: Color temperature is automatically adjusted for light sources in the 2,000ºK to 10,000ºK range
2. MANUAL: To adjust the white balance manually
   • Select MANUAL using the UP or DOWN button and press the MENU button to activate the WB MANUAL option.
   1. RED: To adjust the density of RED (0 to160)
   2. BLUE: To adjust the density of BLUE ( 0 to 160)
3. PUSH: Push Lock mode fixes the white balance based on current lighting. For best results, place a white surface (such as a piece of paper) in front of the camera during adjustment.

AGC (Automatic Gain Control )
Select AGC using the UP or DOWN button. You can select between OFF, ON using the LEFT or RIGHT button.

• AGC is fixed at a certain level in IR LED mode.
• AGC level is selectable in COLOR, B/W mode.

1. ON: Select ON using the LEFT or RIGHT button and press the MENU button to activate the AGC option.
2. LEVEL: You can adjust between 0 to 20 using the LEFT or RIGHT button.
3. OFF: Disable the AGC

DAY/NIGHT
Select DAY NIGHT using the UP or DOWN button. You can select between IRED, COLOR, or B/W using the LEFT or RIGHT butto.

1. COLOR: for color mode only (DAY mode)
2. B/W: for BLACK and WHITE mode only (NIGHT mode) Select B/W using the LEFT or RIGHT button and press the MENU button to activate the COLOR BURST option.
3. IRED: IR LED control mode
   • WIDE: LED control based on full-screen exposure. Some areas may be overexposed.
   • SMART: LED output is limited to optimized scene exposure.

IMAGE ADJ (Image Adjust)
Select IMAGE ADJ using the UP or DOWN button and press the MENU button to activate the IMAGE ADJ mode.

1. SBLC (Super Back Light Compensation): To lighten a darker part of the image

   • Select SBLC using the UP or DOWN button. You can select between OFF, LOW, MIDDLE, and HIGH using the LEFT or RIGHT button.
   • SBLC turns to OFF automatically at night.

2. DNR (Digital Noise Reduction): To reduce the image noise, especially during low ambient lighting conditions.

   • Select DNR using the UP or DOWN button. You can adjust between OFF, LOW, MIDDLE, and HIGH using the LEFT or RIGHT button.

3. SHARPNESS: To adjust the SHARPNESS of the image.

   • Select SHARPNESS using the UP or DOWN button.
   • Select and press the MENU button to activate the SHARPNESS option.
   • You can adjust the sharpness from 0 to 20 using the LEFT or RIGHT button.

4. MIRROR

   • Select MIRROR using the UP or DOWN button. You can select from ON/OFF using the LEFT or RIGHT button.
   1. ON: Horizontal image flip.
   2. OFF: default

5. MOTION (Motion Detect) Display only (No output signal)
   Select MOTION using the UP or DOWN button and press MENU button to activate the MOTION DETECT option.

6. AREA: To specify the MOTION DETECTION area
   Select AREA using the UP or DOWN button. You can select from area 1 to 4 position using the LEFT or RIGHT button.

7. DISPLAY: To display MOTION DETECTED area on the video
   Select DISPLAY using the UP or DOWN button. You can select between ON/OFF using the LEFT or RIGHT button.

8. ON: display the MOTION-DETECTED area on the screen

9. OFF: disable

10. SENSITIVITY: To set up the motion sensitivity
    Select SENSITIVITY using the UP or DOWN button. You can adjust the motion sensitivity of a movement from 1 to 24 using the LEFT or RIGHT button.

11. 1: most sensitive (highest)

12. 24: least sensitive (lowest)

13. TOP/BOTTOM/LEFT/RIGHT: Users can specify the MOTION DETECTED area.
    Select TOP, BOTTOM, LEFT, or RIGHT using the UP or DOWN button. You can adjust the AREA using the LEFT or RIGHT button.
    (NTSC/PAL)

14. TOP: extend or reduce the upper area of the MOTION DETECTED area (8 to 126 / 10 to 146)

15. BOTTOM: extend or reduce the bottom area of the MOTION DETECTED area (8 to126 / 11 to 149)

16. LEFT: extend or reduce the left side of the MOTION DETECTED area (4 to 191 / 8 to191)

17. RIGHT: extend or reduce the right side of the MOTION DETECTED area (4 to 191 / 9 to 192)

18. INITIAL: To reset the MOTION DETECT mode.
    Select INITIAL using the UP or DOWN button. You can reset the MOTION DETECT mode using the MENU button.

19. RETURN: To return to IMAGE ADJ MENU
    Select RETURN using the UP or DOWN button. You can return to IMAGE ADJ MENU using the MENU button.

20. PRIVACY
    Select PRIVACY using the UP or DOWN button and press the MENU button to activate the PRIVACY option.
    NTSC(PAL)

21. 1. AREA: To specify the PRIVACY area
       Select AREA using the UP or DOWN button. You can select an area from 1 to 4 positions using the LEFT or RIGHT button.

22. DISPLAY: To display the Privacy Zone area
    Select DISPLAY using the UP or DOWN button. You can select between ON/OFF using the LEFT or RIGHT button.

23. ON: display the Privacy Zone area

24. OFF: disable

25. COLOR: To change the colour of the privacy zone
    Select COLOR using the UP or DOWN button. You can adjust from WHITE, YELLOW, GREEN, BLUE, RED, BLACK, or GRAY using the LEFT or RIGHT button.
    

26. TOP/BOTTOM/LEFT/RIGHT: Users can specify a PRIVACY ZONE area
    Select TOP, BOTTOM, LEFT, or RIGHT using the UP or DOWN button. You can adjust the privacy zone using the LEFT or RIGHT button.
    (NTSC/PAL)

27. TOP: extend or reduce the upper area of the PRIVACY area (4 to 63 / 6 to 74)

28. BOTTOM: extend or reduce the bottom area of the PRIVACY area (5 to 64 / 7 to 75)

29. LEFT: extend or reduce the left side of the PRIVACY area (18 to 205 / 22 to 206)

30. RIGHT: extend or reduce the right side of the PRIVACY area (19 to 206 / 23 to 207)

31. INITIAL: To reset to factory default only on the PRIVACY mode.
    Select INITIAL using the UP or DOWN button. You can reset the PRIVACY mode using the MENU button.

32. RETURN: To return to IMAGE ADJ MENU
    Select RETURN using the UP or DOWN button. You can return to IMAGE ADJ MENU using the MENU button.

33. COLOR GAIN
    Select COLOR GAIN using the UP or DOWN button and then press the MENU button to activate the COLOR MODE option.

34. INITIAL
    To reset to factory default only on the IMAGE ADJ mode.

    • Select INITIAL using the UP or DOWN button and reset the\ IMAGE ADJ mode using the MENU button.

35. RETURN
    To return to MAIN MENU

    • Select RETURN using the UP or DOWN button and return to MENU using the MENU button.

GENERAL

Select GENERAL using the UP or DOWN button and press the MENU button to activate the GENERAL mode.

1. CAM TITLE

   • Select CAM TITLE using the UP or DOWN button.
     You can adjust ON/OFF using the LEFT or RIGHT button.
   1. ON: To display the camera title on the screen
   2. OFF: disable
   • Select ON and Press the MENU button to display the CAM TITLE.
   1. UP/DN: To select a character using the UP or DOWN button (0 to 9, A to Z)
   2. LE/RI: To select the position using the LEFT or RIGHT button.

2. LANGUAGE – English LANGUAGE.

3. VERSION – Displays the firmware version.

4. INITIAL: To reset to factory default only on the GENERAL mode.

   • Select INITIAL using the UP or DOWN button.
     You can reset to factory default for GENERAL mode using the MENU button.

5. RETURN: To return to MENU

   • Select RETURN using the UP or DOWN button. You can return to the MENU using the MENU button.

• INITIAL: To reset to factory default.
  Select INITIAL using the UP or DOWN button and reset to factory default using the MENU button.

• EXIT: To exit the OSD setup menu.
  Select EXIT using the UP or DOWN button and close the OSD setup menu by pressing the MENU button.

SPECIFICATION

TROUBLESHOOTING

If you have trouble operating your camera, refer to the following guidelines. If the guidelines do not help you to solve the problem, contact an authorized technician.

Nothing appears on the screen

• Check that the power cord and the video cable between the camera and monitor are properly connected.
• Check that you have properly connected the VIDEO cable to the camera VIDEO output jack.

The image on the screen is dim

• If the lens is obstructed (for example, with dirt), clean the lens with a soft, clean cloth.
• Set the monitor to proper condition.
• If the camera is exposed to too strong light, change the camera position.
• Adjust the lens’ focus properly.

The image on the screen is dark

• Adjust the contrast feature of the monitor.
• If you loop through an intermediate device, set the termination (75 Ohms / Hi-Z) properly.

Design and specifications are subject to change without notice.

References

• Honeywell Security | Honeywell

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>