Swiss Madison SM-1T256 One Piece Toilet Instruction Manual
- June 17, 2024
- Swiss Madison
Table of Contents
Swiss Madison SM-1T256 One Piece Toilet
Product Specifications
- Product: One-Piece Toilet
- Manufacturer: Swiss Madison
- Contact: 434-623-4766">1-434-623-4766 | [email protected]
Product Usage Instructions
Installation
- Before Installation: Contact customer support for any questions or concerns.
- Included Parts: Wax Ring/Gasket, Cover Caps, Bolts, One-Piece Toilet.
- Suggested Tools & Materials: Safety Glasses, Putty Knife, Tape Measure, Wrench, Level, Flexible Hacksaw, Screwdriver, Supply Tube.
- Install Closet Bolts: Secure the closet bolts in place.
- Install Wax Seal: Place the wax ring on the closet flange.
- Toilet Seat Installation: Disassemble the seat, construct hinges at the bottom of the screw, attach hinges, adjust and cover hinges, adjust and attach the seat until you hear a click.
Frequently Asked Questions (FAQ)
-
Q: What is the warranty on the One-Piece Toilet?
A: The product comes with a one-year limited warranty. Contact customer support for any warranty-related issues. -
Q: What should I do if I encounter damages during installation?
A: Contact us directly at 1-434-MADISON (623-4766) for assistance with damages or accidents during installation.
BEFORE INSTALLATION
-
Inspect the toilet to ensure no damages have occurred while in shipping.
-
Observe all plumbing and building codes per your state and local requirements.
-
All dimensions are nominal! Be sure to measure your toilet before installation.
-
The step-by-step guidelines in the installation instructions are a general reference.
Should there be any discrepancies, Swiss Madison cannot be held liable. It is recommended to install all Swiss Madison products by hiring a licensed professional. -
Read installation and maintenance instructions thoroughly before installing.
Be sure to use proper tools and always wear proper personal safety accessories for your protection. -
Two people are recommended to handle and install this product as it is fragile.
QUESTIONS OR CONCERNS?
Please contact us:
1-434-623-4766
[email protected]
INCLUDED PARTS
SUGGESTED TOOLS & MATERIALS
INSTALLATION:
Turn Off the Water Supply
- Close the toilet supply valve and flush the tank completely, use the towel to remove excess water.
- Disconnect and remove the supply line, if you are replacing the valve shut the main water supply first.
- Remove closet bolts from the flange and clean wax and putty from the base area.
Rough-In the Toilet
- Measure the wall from behind the toilet to the middle of the closet bolt. Your rough-in measurement should be 12″.
Install Closet Bolts
- Install closet bolts to flange channel, turn 90°, and slide into place 6″ (152mm) apart and parallel to the wall.
Install Wax Seal
- Invert the toilet on the floor (use the cushion to prevent damage), and install a wax ring evenly around the waste flange with the tapered end of the ring facing the toilet. Apply a thin bead of sealant around the toilet base.
Position the Toilet on the Flange
- Unplug the floor waste opening and install the toilet on the closet flange so bolts project through the mounting holes.
- Loosely install retainer washers and nuts.
Install Toilet
- Position the toilet square to the wall and, with a rocking motion, press the bowl down fully on the wax ring and flange. Alternately tighten nuts until the toilet is firmly sealed to the floor. Do not over-tighten nuts, it might crack the ceramic.
- Smooth off the bead of sealant around the base. Remove excess sealant.
- Place cover caps to hide installation holes on the toilet.
- Connect the water supply to shut off the valve, and check for leaks. Tighten if necessary.
TOILET SEAT INSTALLATION
Disassemble
- Disassemble the cover cap and the hinge.
Construct Hinges
- Insert the screw and nut into the hole on the hinge.
- Attach blind hole screw fixing to the bottom of the screw.
Attach Hinges
- Insert hinges with blind hole screw fixings attached into holes on the toilet bowl.
- Lightly tighten hinges with a screwdriver to allow for later adjustment.
Adjust and Cover Hinges
- Be sure the hinge is all the way forward for proper seat fitting.
- Place the covers onto the hinges.
Adjust and Attach the Seat
- Align the seat to the hinges then firmly tighten the hinges.
- Attach the seat to the secure hinges.
- Adjust the seat to align to the bowl.
TOILET SEAT USAGE
- To remove, push the middle button until you hear a “click”, then pull straight up.
- To re-install, align hinge posts with reference marks on the seat, then push down until you hear a “click”.
ONE-YEAR LIMITED WARRANTY
Swiss Madison® products are made with quality materials and excellent craftsmanship to provide our customers with beautiful, durable, long-lasting products. Should there be any defects in materials or craftsmanship under regular use that are discovered within the first year of installation, Swiss Madison® will provide replacement parts at no charge, or at its discretion, replace any product or part of the product that is deemed defective, under normal installation, use, service or maintenance. This warranty applies only to the original purchaser. Proof of purchase will be required in the instance of a claim. Swiss Madison® recommends all installations of Swiss Madison® products be conducted by a licensed, professional plumber or contractor. Swiss Madison® will not be held responsible for any damage or product failure due to improper installation, misuse, or failure to utilize a licensed professional for installation. Swiss Madison® is not responsible for any installation or removal costs.
THIS ONE-YEAR LIMITED WARRANTY WILL BE VOIDED IF:
- The installation recommendations were not followed by the installer
- The product has been moved from its initial place of installation
- The product has in any way been modified from its packaged state
- The product has been subjected to improper maintenance, abuse, misuse, excessive use of chemicals, accidents, or other damages, etc.
Swiss Madison® makes no implication that its products comply with any local building or plumbing codes. It is the consumer’s responsibility and obligation to determine local code compliance before and during installation. This warranty extends only to the original purchaser and first consumer. Swiss Madison® is not responsible for any special, incidental or consequential damages associated with the installation, replacement, return or use of the original purchaser’s product. This includes, but is not limited to: freight costs labor, travel time, lost profit, home damages, and other contingent liabilities and costs (including, without limitation, costs associated with ‘professionals’ or ‘experts’, investigations, audits, analyses, attorneys and any other professional/hired services). The Swiss Madison® warranty is a comprehensive and explicit limit of liability. All items not disclosed within the warranty are not addressable within the responsibility of Swiss Madison®. Certain states have variances regarding implied warranties; in those situations, we remain fully compliant.
QUESTIONS OR CONCERNS?
Please contact us directly at 1-434-MADISON (623-4766)
WARNING:
Contents of your order may contain sharp and possibly other harmful pieces and
may cause hazard to children and adults. Swiss Madison® is not responsible in
any way for personal damages.