fontastic Boncy Bone Conduction Headset User Manual
- June 17, 2024
- fontastic
Table of Contents
**fantastic Bouncy Bone Conduction Headset User Manual
**
User Manual
Thank you for choosing the Fantastic® bone sound headset „Bouncy“. Please read the operating instructions carefully and observe the safety instructions. Please keep this user manual for future reference.
Package contents
- Bone Conduction Headset Bouncy
- USB -Type-C® charging cable
- Operating Instructions
Overview
- Volume – | previous track
- Multifunction button (power button, phone, music start/stop)
- Volume + | next track
- Speaker
- Microphone
- UBS Type-C® charging port
- Neckband
Note : Fully charge the headset before using it for the first time.
Power On/Off
Press the multifunction button for 2 seconds, the headset will turn on.
Press the multifunction button for 2 seconds, the headset will turn off.
Pairing
Bouncy must be paired with a Bluetooth® device before it can be used as a
hands-free wireless headset.
- Put Bouncy in pairing mode by pressing and holding the multifunction button for at least 2 seconds while it is off. Bouncy turns on. The LED will flash red and blue, this indicates pairing mode.
- Search for „Bouncy“ on your Bluetooth® enabled device and select it from the list of found devices to pair the headset with the Bluetooth® device.
- Confirm the connection with Bouncy.
If you are not sure how pairing works on your Bluetooth® device, please refer to the device‘s user manual.
If using a Bluetooth® device without a display, switch it to pairing mode and wait a few seconds for the Bouncy to connect
Note : If the headset does not find a Bluetooth®-enabled device, it will turn off after approximately 2 minutes
Music control
Note : The cell phone must support A2DP and AVRCP profile to play and
control music through the headset
Start/Stop : To play or stop music, press the multifunction button briefly.
Previous track : To skip to the previous track, press and hold the volume- button.
Next track : To skip to the next track, press and hold the Volume+ button.
Handsfree functions
Due to the built-in microphone, the Fantastic® Bouncy is perfectly suited to
be used as a hands-free device for phone calls.
Answer incoming call : Briefly press the multifunction button.
End ongoing call : Briefly press the multifunction button.
Reject incoming call : Press and hold the multifunction key.
Voice assistant
Double-tap the multifunction button to activate the voice assistant.
Setting the volume
Increase volume : Briefly press the Volume+ key. Repeat this step until
the desired volume is reached.
Decrease volume : Briefly press the Volume- key. Repeat this step until the desired volume is reached. is reached.
Note : Rarely it happens that the super bass of the headset is overdriven by settings of the cell phone.“ In this case, use the „Normalize“ function (also „Adjust volume“) in the audio settings of the smartphone
Safety instructions
- Do not operate the headset at the highest volume for extended periods of time.
- Stop using the headset in dangerous situations.
- Never open the device
- Do not immerse the device in water and protect it from moisture.
- Unplug electronic devices when not in use for an extended period of time.
- The product is not a toy for children.
- The product is not suitable for children because of the high volume.
- Do not use the device if it shows visible damage.
- Charge the headset at least once every 6 months.
- Do not store the product in extreme temperatures (below 0°C or above 45°C).
- Do not use chemicals or detergents to clean the product.
- Do not attempt to disassemble the device.
Technical data:
- BT version 5.3
- Profiles: Headset, Handsfree, A2DP, AVRCP
- Range: up to 10 m
- Driver: 11.2 mm
- Frequency: 20Hz-20KHz
- Sensitivity: 84±3dB
- Impedance: 8Ω
- Maximum power: 500mW
- Status LED
- IPX5 splash water protection
- Voice announcement: German/English
- Housing material: ABS
- Battery: 180 mAh Li-polymer
- Charging port: USB Type-C
- Operating time: Up to 8 hrs (at 50% volume)
- Charging time: Approx. 2 hrs.
- Dimension: 130 x 110 x 46mm
- Weight: 40g
The company is not responsible for any damage due to improper operation.
If you need technical support, please contact our support team by e-mail at service@fontastic.eu
We hereby declare, that this device carries the CE mark in accordance with the regulations and standards. It conforms with the fundamental requirements of the (RED) 2014/53/EU directive.
The full text of the EU Declaration of Conformity is available at the following Internet address: www.d-parts.de/Konfo
Note on environmental protection:
After the implementation of the European Directive 2012/19/EU in the national
legal system, the following applies: Electrical and electronic devices may not
be disposed of with domestic waste. Consumers are obliged by law to return
electrical and electronic devices at the end of their service lives to the
public collecting points set up for this purpose or point of sale. Details of
this are defined by the national law of the respective country. This symbol on
the product, the instruction manual or the package indicates that a product is
subject to these regulations. By recycling, re-using the materials or other
forms of utilizing old devices, you are making an important contribution to
protecting our environment.
