PHYLRICH 222-02 Widespread Faucet Square Handles Turqoise Accents Installation Guide

PHYLRICH 222-02 Widespread Faucet Square Handles Turqoise Accents

Product Specifications

• Model: JOLIE 222-02
• Valve Type: Dry Tee Flush Mounted
• Spout Hole Diameter: 1 3/8 inches
• Drain Hole Diameter: 1 1/4 inches
• Flex Lines Material: Stainless Steel

Product Usage Instructions

Installation Steps

1. Step 1 – Spout Installation: Insert spout base nipple into the center hole in the lavatory or countertop. Secure with stainless washer and nut.
   Should a counter top need to be drilled, please reference the diagram above.

2. Step 2 – Spout Tee Assembly: Install the spout tee assembly according to the provided diagram.
   Insert spout base nipple into center hole in lavatory or counter top. Install stainless washer (5) nut (6) on spout nipple and tighten

3. Step 3 – Valve Installation: Install the lavatory valves, ensuring correct orientation based on handle sets. Adjust rough-in height and secure the valves.
   Install spout tee assembly (7) as shown in diagram.

4. Step 4 – Drain Assembly: Insert pre-assembled drain rim into the basin and connect the drain components as instructed.
   Remove top fastening nut and washer (1) from the lavatory valve. (NOTE A: All lever handle sets are supplied with one righthand valve and one left-hand valve. Install valve with blue dot on the cold side [Round handle sets are supplied with two hot valves that turn in the same direction]). Insert valve from below through hole in lavatory or countertop.

5. Step 5 – Flex Lines Connection: Connect stainless steel flex lines from valve outlets to spout tee, ensuring no kinks. Install escutcheons and handles onto valve stems.
   Reattach top fastening nut and washers (1).

6. Step 6 – Final Assembly: Place the pre-assembled base over flush mount, connect the cage handle, and tighten set screws for final assembly.
   Set valve to proper rough-in height “A”, by adjusting bottom – fastening nut. Secure valve by tightening top fastening nut. Repeat procedure for the second lavatory valve.

7. Step 7 – Connect stainless steel flex lines (9) from valve outlets to spout tee (7). Flex lines should be looped as shown in diagram. FLEX LINES MUST NOT BE KINKED. Adjust valves and or spout teeto eliminate any kinking in the flex lines. Install escutcheons onto the valves and hand tighten. DO NOT OVER-TIGHTEN. Install handles onto valve stems.

8. STEP 8 – DRAIN ASSEMBLY
   Insert *Pre-assembled drain rim (A) into the basin placing the Teflon washer (B) under the rim. From below slip on washer (C) onto the bottom thread of the drain rim and secure to basin with drain nut and washer (D & E) then insert Tail tube drain (F) onto the drain rim (A).

9. Step 9 – THIS STEP MUST BE COMPLETED TO ADHERE TO THE LIMITED LIFETIME WARRANTY. Flush hot and cold supply lines before connecting faucet to supply lines. Connect the supplies to the bottom of the lavatory valves using the brass coupling nuts provided or with a flexible line. Connect your waste P-trap to the drain tail piece.

10. Step 10 – Handles Assembly
    Place the pre-assembled base (A) over flush mount. Align base and secure using centering nut (D). Connect the pre-assembled cage handle (B) on to broach then tighten set screw (C) for final assembly.

Note: Ensure Washer (E) is properly inserted underneath the handle hub to avoid the cage handle from damaging the base.

LIMITED WARRANTY

This Limited Warranty is expressly in lieu of any other warranties, expressed or implied, arising by law or otherwise, including without limitation, any implied warranty of merchantability or fitness for a particular purpose. This Limited Warranty may not be altered, varied, or extended, except by a written instrument executed by Phylrich. The remedy repair or replacement as provided under this Limited Warranty is exclusive. In no event shall the manufacturer be liable for any consequential or incidental damages to any person, whether or not occasioned by the negligence of Phylrich, including without limitation damages for loss of use, costs of property damage or other monetary loss. Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
This warranty covers products installed in the United States and Canada.
Several types of limited warranties are applicable to decorative plumbing and hardware products as follows. Mechanical Warranty: This warranty covers the ability of the product to function properly under normal conditions. Our products are warrantied to the original purchaser to be free of defects in material and workmanship for a period of 10 years from the date of purchase.
Because plumbing valves have several mechanical differences due to their function i.e. faucet valves vs. thermostatic shower valves, the following valve warranties are established:

• Ceramic disc valves are warranted for life as long as the original purchaser owns the house in which they are installed.
• Other types of valves, including thermostatic and balance pressure shower valves, etc. are warranted for one year from the date of purchase.

Finish Warranty: Because certain metal finishes are more durable than others and certain applications require more durability, 4 finish warranties have been established:

• Certain metal finishes such as antique brass, satin nickel and satin brass are coated with an organic clear coating.
• These coated types of finishes are warranted for 10 years from the date of shipment to the original purchaser.
• Finishes with harder surfaces such as polished chrome, Physical Vapor Deposition (PVD) finishes and powder-coated finishes are warranted as long as the original purchaser owns the home.
• The so-called “living finishes” are not warranted. These finishes have no protective coating and thus are designed to change with age and use.
• Finishes on Drains: Because of the use and abuse of the metal surface that occurs on sink and bath drains with soap and cleaning solutions, only drains in the “B” category above are warranted. This warranty is for one year from the date of purchase. Drains in the above A and C categories are not warranted.

The warranties described above are specific rights, but there may be other rights that vary from state to state. If you have a problem with one of our products, here is what is covered and how you should proceed:
First of all, consult the dealer from whom you purchased the product. Please provide proof of purchase in the form of an original invoice or receipt. If the dealer is an authorized Phylrich dealer, he will review the problem and contact the Phylrich customer service department on your behalf. If you cannot contact your dealer, please e-mail our customer service at customer.service@phylrich.com and describe the problem along with your contact information.
The Phylrich Warranty does not assume liability for charges such as labor, freight, removal reinstallation or injuries resulting from a defective product. Phylrich will repair or replace defective parts after it has been established that the product is defective and that the parts are covered by this warranty. Phylrich reserves the right to determine whether to repair or replace the product under consideration.
Phylrich products must be installed in accordance with the instructions provided with the product. Make sure your installer flushes out all debris such as solder before final assembly. The plumber’s putty should not be used on any decorative surface as it could harm the finish and void the warranty.
For proper maintenance do not use any abrasive cleaners, strong cleaning solutions, or polishing compounds. Usually, a soft damp cloth will suffice. Non-abrasive waxes can also be used.

Frequently Asked Questions (FAQ)

Q: What is the warranty coverage for this product?

A: This product is covered by a limited lifetime warranty in the United States and Canada. Mechanical warranty covers proper function for 10 years from the date of purchase.

Q: Are supply lines and angle stops included with the product?

A: No, supply lines and angle stops are not included. They must be sourced separately for installation.

Q: How should I adjust the valves and spout tee to avoid kinking in the flex lines?

A: Properly adjust the valves and spout tee as per the provided diagram to ensure the flex lines are not kinked during installation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>