GOLDEN LIGHTING 3160-6 NB-HWG Calla 6 Light 28 Wide Taper Candle Style Chandelier Instruction Manual
- June 17, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 3160-6 NB-HWG Calla 6 Light 28 Wide Taper Candle Style
Chandelier
Product Information
Specifications:
- Model: 3160-6 NB-HWG
- Height: 8′
- Width: 30
- Weight: 5’9
- Voltage: 36
- Wattage: 28
Product Usage Instructions
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of island. Fixtures should hang at least 30″ above the countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.
To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment.
For installation instructions and wire connections, refer to the assembly instructions provided.
FAQ
How do I identify the fixture’s wires?
The fixture wires are typically labeled as Hot, Neutral, and Ground. Match these with the corresponding house wires for proper installation.
What should I do if I need replacement parts?
Contact the place of purchase for customer service to arrange for replacement parts.
Thank You for Choosing Golden Lighting for Your Lighting Needs!
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
How to Identify the Fixture’s Wires
- Hot: Smooth, Black, or Transparent with Black Inner Thread
- Neutral: Ribbed, White or Transparent with White Inner Thread
- Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
Get help, quick tips, and explore curated content
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions:
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove old fixture from wall, including the old
mounting strap. 1. From the parts bag remove the mounting strap (A) assembly.
One end of the nipple (F) should be attached to the mounting strap (A) with
washer (C) and hex nut (D) in place. The other end should have a canopy loop
(H) attached. Attach mounting strap (A) to the junction box using mounting
screws (B) and a screwdriver. Tighten securely. Unscrew canopy loop collar (I)
from canopy loop (H). Pass canopy (G) over the mounted canopy loop (H) to test
the height. Approximately half of the canopy loop’s exterior threads should be
exposed, and the canopy loop collar (I) should fit snugly onto the canopy loop
(H). Remove canopy (G) and adjust the height of nipple (F) and canopy loop (H)
until the desired height is reached.
ASSEMBLING THE FIXTURE
2. Thread column (L) onto nipple (N) to secure the column and top loop piece
to the fixture. Pull the wires until taut. Measure to determine the correct
length of chain needed for proper hanging height. If necessary, use a pair of
pliers to open and remove any excess chain. Attach each of the chain
connectors (K) to each end of chain (J) before attaching one end of the chain
connector/chain to top loop (L). Connect the other chain connector (K) to the
canopy loop (H). Close the chain connectors (K) to secure. Feed the fixture’s
wires up through the chain (J) (every three links or so), pulling the wires
until gently slide canopy loop collar (I) and canopy (G) down onto the
chain/wires. Trim excess wires leaving about 8 to 10 inches for later.
CONNECTING THE WIRES
3. Have an assistant support the fixture’s weight while completing the
wiring. Refer to the wiring diagram and attach the fixture’s wires to the
power supply wires from the junction box. Attach the fixture’s wires to the
power supply wires from the junction box. Connect Hot to Hot (transparent wire
with black inner thread, black, or smooth wire) Neutral to Neutral
(transparent wire with white inner thread, white, or ribbed wire), and Ground
to Ground (transparent wire with green inner thread, green wire, or copper).
Twist the ends of the wire pairs together, and then twist on a wire connector.
Make sure all twists are in the same direction. If there is no house ground
wire coming from the junction box, locate ground screw (E) on the mounting
bracket/mounting strap and wrap the fixture’s ground wire around the ground
screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires
and into the mounting bracket/mounting strap. Tuck the wires into the junction
box.
FINISHING THE INSTALLATION
4. Push canopy (G) up to the ceiling and slide canopy loop collar (I) up
beneath the canopy. Tightly thread canopy loop collar (I) onto canopy loop (H)
to secure canopy in place until snug against the ceiling. Attach glass panels
- GoldenLighting.com
- @GoldenLighting
- @GLFixtures
- @GoldenLighting1
- @GoldenLighting
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>