DYNOJET PC6-20009 Power Commander 6 Installation Guide
- June 4, 2024
- Dynojet
Table of Contents
DYNOJET PC6-20009 Power Commander 6 Installation Guide
PARTS LIST
- 1 POWER COMMANDER 6
- 1 INSTALLATION GUIDE
- 1 USB CABLE
- 2 DYNOJET DECALS
- 2 POWER COMMANDER DECALS
- 2 VELCRO STRIPS
- 1 ALCOHOL SWAB
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION. THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
INPUT 1 INPUT 1 INPUT 2
OPTIONAL ACCESSORY INPUTS
Map
(Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You
can switch on the fly between these two base maps when you hook up a switch to
the MAP inputs. You can use any open/close type switch. The polarity of the
wires is not important.
Shifter
(Input 1 or 2) Used for clutch-less full throttle upshifts. Insert the wires
from the Dynojet quick shifter into either
Input 1 or Input 2. The polarity of the wires is not important. Set to Input 2
by default.
Speed
If your application has a speed sensor then you can tap into the signal side
of the sensor and run a wire into this input. This will allow you to calculate
gear position in the Control Center Software. Once gear position is setup you
can alter your map based on gear position and setup gear dependent kill times
when using a quick shifter.
Analog
This input is for a 0-5v signal such as engine temp, boost, etc. Once this
input is established you can alter your
fuel curve based on this input in the Power Core software.
Launch
You can connect a wire to either Input 1 or Input 2 and then the other end
to a switch. This switch when engaged (continuity) will only allow the RPM to
be raised to a certain limit (set in the software). When released, you will
have full RPM.
WIRE CONNECTIONS
To input wires into the PC6 first remove the rubber plug on the backside of
the unit and loosen the screw for the corresponding input. Using a 22-24 gauge
wire, strip about 10mm from its end. Push the wire into the hole of the PC6
until it stops and then tighten the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make inserting them easier.
INSTALLING THE POWER COMMANDER 6
-
Remove the main seat and the passenger seat.
-
Prop the front of the fuel tank up using the Suzuki prop rod.
-
Remove the air box.
The air box does need to be removed to perform this installation but may make it easier as the stock injector connectors can be very difficult to remove. -
Route the PC6 harness from the tail section towards the engine.
-
Locate the stock injector connectors. One is BROWN (front cylinder) and one is GREY (rear cylinder). Unplug these connectors from the injectors.
-
Plug the connectors from the PC6 in-line of the stock wiring harness and the injectors. Connect the ORANGE wires from the PC6 to the front cylinder and stock BROWN connector. Connect the YELLOW wires from the PC6 to the rear cylinder and stock GREY connector.
-
Locate the Throttle Position Sensor connector located on the left side of the throttle body.
-
Unplug the connector from the TPS.
-
Plug the 3-pin connectors from the PC6 in-line of the TPS and stock wiring harness.
-
Attach the ground wire from the PC6 to the negative side of the battery.
-
Using the supplied Velcro, install the PC6 in the tail section. Clean both surfaces with the supplied alcohol swab prior to applying the Velcro adhesive.
-
Reinstall the air box if it was removed and bolt the fuel tank back down. Install the main seat and the passenger seat.
Download the latest map files from our web site at dynojet.com/tunes. Optional
inputs:
Speed input – PINK wire – connector is located in front of the air box – comes
from front wheel.
Temperature input – BLACK/BLUE wire of sensor on thermostat housing.
12v source for Autotune – BROWN wire of 3-pin connector for the tail light.
2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081 – 800-992-4993 – DYNOJET.COM © 2007-2022 DYNOJET RESEARCH ALL RIGHTS RESERVED
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>