Fontastic 263286 Wireless On Ear Headphone User Manual

Wireless On-Ear Headphone
with active noise cancellation
Tonic User Manual

Thank you for purchasing this Fontastic ® headphones „Tonic“ with active noise cancellation. Please read the Manual carefully and observe the safety instructions. Please keep these operating instructions for future reference.

Package contents

• Fontastic® Headphone Tonic
• USB charging cable
• 3.5 mm audio cable
• This user manual

Overview

1. ANC LED
2. ANC switch
3. Volume+ | next track
4. Volume- | previous track
5. Multifunction button (on/off, music start/stop, phone functions)
6. Status LED| 7. USB Type-C port
8. 3.5 mm line-in port
9. Microphone
10. Speaker
11. Height adjustment
---|---

Charging the battery

The Fontastic® Tonic is equipped with an internal rechargeable battery. Connect the Tonic with the USB Type-C ® cable which is included in the package contents.
The cable can be connected to a computer or a standard USB power supply. The Tonic‘s red LED lights up during the charging process. When fully charged, the red LED goes out.
The cable can be disconnected from the Fontastic® Tonic.
Note: Fully charge the Tonic before using it for the first time.

Adjusting the height / folding the speakers
To adjust the height, hold the speaker unit and pull the headphone bracket upward.
Adjust the headphones in this way until the ear pads sit exactly on the ear. The headphones can be folded for space-saving storage or transport.

Switching On /Off

To switch on, press the multifunction button for 3 seconds, an acoustic signal sounds, the blue and red LED flash alternately.
To switch off, press the multifunction button for 3 seconds, an acoustic signal sounds, the LED goes off.

Pairing

Tonic must be paired with a Bluetooth ® device before it can be used as wireless headphone with hands free function.

1. In the off state, press and hold the multifunction button (5) for 3 seconds to turn on. Keep the button pressed and wait until the blue and red LED flashes alternately. This indicates the pairing mode.
2. Search for „Tonic“ on your Bluetooth ® enabled device and select it from the list of found devices to connect the headphones to the Bluetooth® device.
3. Confirm the connection with Tonic.

If you are unsure about the pairing procedure of your Bluetooth ® device, please check your device manual. When using a Bluetooth ® transmitter without display, set it to pairing mode and wait a few seconds until the connection with Tonic is established. Note: If the connection is lost or the transmitter is temporarily disconnected, briefly press the multifunction button. Tonic will then try to restore the connection.
Note: The connection is disconnected during the charging process. The headphones turn off, and the on/off button is disabled.

ANC Noise Cancellation

Tonic is equipped with active noise cancellation to reduce ambient noise and enhance music enjoyment.
To activate the ANC function, press the ANC switch. Activated ANC is indicated by the green LED lighting up.

Music playback

Note: The mobile phone must support the A2DP and AVRCP profile for wireless music streaming and control. The buttons have no function when using the wired connection. Use the audio source to control the music and volume. Start music playback on the Bluetooth ® source which is paired with the Tonic. The music is transferred to the Tonic. Stop the music playback on the Bluetooth ® source to interrupt the streaming. To start or stop music playback via the Tonic, press the multifunction button once.
By using an 3.5 mm jack cable, you can also use Tonic as wired headphones when it is turned off. To do this, connect the cable to the 3.5 mm line-in port of Tonic and the audio source, start music playback on the audio source.
NOTE: The buttons on the Tonic have no function when using an audio cable.

Music control

Start/Stop: To play or stop music, press the multifunction button briefly.
Previous track: To skip to the previous track, press and hold the volume- button.
Next track: To skip to the next track, press and hold the Volume+ button.

Handsfree functions

Due to the built-in microphone, the Fontastic® Tonic is perfectly suited to be used as a hands-free device for phone calls.
Answer incoming call: Briefly press the multifunction button.
End ongoing call: Briefly press the multifunction button.
Reject incoming call: Press and hold the multifunction button.
Redial: Press the multifunction key twice button.

Volume setting

Increase volume: Briefly press the Volume+ key. Repeat this step until the desired volume is reached.
Decrease volume: Briefly press the Volume- key. Repeat this step until the desired volume is reached.

Technical data:

• BT version 5.3
• Profiles: Headset, Handsfree, A2DP, AVRCP
• Range: approx. 10m
• Input: 5V DC
• Frequency range: 20Hz-20kHz
• Impedance: 32Ω
• Driver: Φ 40mm
• Noise reduction: 20db
• Built-in high performance microphone
• 3.5mm audio line-in connector
• USB Type-C charging port
• Battery: 400mAh
• Operating time: BT up to 40 hrs | BT+ANC up to 25 hrs.
• Charging time: Approx. 1.5 hours
• Weight: 175g

Safety advice:

• Do not open the device
• Do not hold the device under water
• Keep it safe from humidity
• Do not connect the adapter to the device by using force
• Keep the device away from children
• Disconnect electronic devices from the power when not using them for longer time.
• Do not use the device when it has visible defects.

No liability is accepted for any damage caused by incorrect operation.
In case you need technical support, please contact our support-team by e-mail under service@fontastic.eu.

Registration and Safety

Certification/General Information
** We hereby declare, that this device carries the CE mark in accordance with the regulations and standards.
It conforms with the fundamental requirements of the RED 2014/53/EU directive.
The full text of the EU declaration of conformity is available at the following internet address: www.d-parts.de/Konfo**

Note on environmental protection:
After the implementation of the European Directive 2012/19/EU in the national legal system, the following applies: Electrical and electronic devices may not be disposed of with domestic waste.
Consumers are obliged by law to return electrical and electronic devices at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details of this are defined by the national law of the respective country.
This symbol on the product, the instruction manual or the package indicates that a product is subject to these regulations.
By recycling, re-using the materials or other forms of utilising old devices, you are making an important contribution to protecting our environment.

The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks is under license.
USB Type-C® and USB-C® are trademarks of USB Implementers Forum.
Improvement and changes of the technical specifications and other data’s could be made without prior notice.
Registered trademarks are the property of their respective owners.

Fontastic, by D-Parts GmbH
Birkenweiher Str. 16
63505 Langenselbold, Germany
www.d-parts.de
V1_0723

Documents / Resources

| Fontastic 263286 Wireless On Ear Headphone [pdf] User Manual
263286 Wireless On Ear Headphone, 263286, Wireless On Ear Headphone, On Ear Headphone, Headphone
---|---

References

• D-Parts GmbH

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>