Trudian TD-D1R88 Network Video Intercom Instruction Manual
- June 17, 2024
- Trudian
Table of Contents
Network Video Intercom
Instruction manual
TD-D1R88
Specifications
Outdoor Phone
| Image Effects | Two million 1080P, 140 degree horizontal angle |
|---|---|
| Nightvision | IR CUT switching, color without color bias, night vision black |
and white image
Unlock| Connected to magnetic lock or electric lock, indoor monitor has latch
delay time setting
7-inch capacitive touch 1024*600 IPS Indoor Monitor
Connection| Connect up to 2 outdoor phones and 6 indoor monitors, indoor
monitors can be interconnected
Network| Indoor monitor connected to 2.4G WiFi
Power| 12V 2A power adapter, four-core cable to connect indoor monitor and
outdoor phone at the same time power supply
Functions| Intercom, photo, video, unlock, visitor record, motion detection
and calendar display
Adjust brightness, contrast and color, latching delay adjustment, multi-
language OSD menu
Extended
Memory| Internal TF card to save automatic photo, video or message
Description and Dimensions
Installation Schematic
Install the outdoor phone at a height of 1.4~1.7m above the ground, avoiding
sun and rain as much as possible. Fixed to wall, board, door with 2 screws or
adhesive tape, also can be installed on the 86 box.
- Drill holes for passing through the 4-core cable, it connects the outdoor phone and indoor monitor, interconnecting audio and video.
- Remove the screws of the waterproof cover with a hexagonal screwdriver.
- Separate waterproof cover and outdoor phone.
- Pass the 4-core wire through the hole in the wall.
- Secure the waterproof cover with two screws.
- Put the outdoor phone in a waterproof cover and fixes the bottom screw.
- Screw the wall bracket for fixing the indoor monitor.
- Connect the other end of the 4-core cable to Door1 or Door2 of the indoor monitor.
- Connect 12V 2A power supply to the indoor monitor.
- Hang the indoor monitor on the wall bracket.
Connect the outdoor phone and indoor monitor
-
The 4-core cable interface of the outdoor phone is the same as that of the indoor monitor.
Connect the 4-core cable, the other end of the 4-core cable is connected to Door1 of the indoor host, and if there are two outdoor phones, connect the other outdoor phone to Door2. -
Connect up to 2 outdoor phones and 6 indoor monitors.
Note: Go to “Settings” -> “System Settings” of the indoor monitor, the device number of the host connected to the outdoor phone is 1, and the indoor extensions are 2,3,4,5,6 respectively.
Doo1, Door2:
Connect the 4-core cable, and the other end of it connects to the outdoor
phone
Connect lock schematic
Note: The electric lock does not distinguish between positive and negative,
unlocking voltage 12V, please check the electric lock unlocking power
specifications purchased separately, the latch delay time please set in the
indoor host.
Introduction to indoor monitor operation
- Tap the screen to enter the settings screen.
System Settings:
Device number: The indoor monitor connected to the outdoor phone is set to 1, and the extensions are numbered 2, 3, 4, 5, 6 in that order.Standby clock display switch| on/off
---|---
Language setting| English, Russian, French, Spanish, German and Simplified Chinese
Key tone| On/Off
Ringback tone switch| On/Off
Outdoor Phone Settings:
Note: The following settings are configured on the host, the extensions are
synchronized with the host settings.
Please check whether Door1 or Door2 is connected, or whether there are two
outdoor phones connected.
Enable switch| If only one outdoor phone is connected, please turn off the
enable for the one that is not connected.
---|---
Latch delay time| After connecting the electric lock, please set the
corresponding lockout time.
Record mode| When someone calls, motion detection trigger, select automatic
video or photo.
Motion detection switch| To turn on or off motion detection
Motion detection sensitivity| Set low / medium / high
Motion detection time| After the triggering motion detection, set the
recording time
Message switch| Turn on/off the function of leaving a message
Message time| Setting the time to leave a message
Signal system| Automatic detection the signal system: PAL / NTSC / automatic
Signal type| The outdoor phone is D1, if you connect other analog outdoor
phone, please select auto-detection in the signal system, so that the outdoor
phone can be used normally
Ringing settings (extension can set the ringing tone)| Set the ringing tone
for 3 time periods, ringing time, 10 kinds of ringing tone to choose one,
ringing volume
Advanced Settings:
Format SD card, factory settings, software upgrade, system reboot
System Information:
Software version, release date, SD space left, UUID
-
Click “Monitor” or press the outdoor phone to call over the interface.
This icon appears when you click to monitor the outdoor phone to switch the outdoor phone
Set Volume, Brightness, Contrast, Saturation This icon appears when you click on the “Call” icon, indicating that a call is in progress, and when you click on it again, the call is still in progress
Hang up
Transfer call, the same position as the icon of switching the outdoor phone, call transfer and internal call are two different forwarding, after answering the outdoor phone call, this icon appears, if you find the visitor is looking for other indoor monitor , you can transfer to the others.
-
Click “Transfer call” to call other indoor monitors, which is equivalent to internal call.
-
Click “Record” to display call records, message records, motion detection records, you can view pictures or Long press the record file to delete, delete all, read all.
-
Click “Devices” to manage the parameters of the doors and cameras settings.
-
Click “Setting” to set parameters such as language, date, etc.
-
Click “Home” mode to switch 3 modes, the indoor monitor should be inserted TF card, and turn on the message switch.
① At home: After the visitor presses the doorbell, the indoor monitor will ring and the phone will receive the notification, click on the notification and answer, if there’s no answer, the visitor will be prompted to leave a message.
② Not at home: After the visitor presses the doorbell, the mobile phone APP will receive the notification, click the notification and answer.
③ Sleep: When the visitor presses the doorbell, the outdoor phone and indoor monitor will not ring or beep, and the mobile phone APP will receive the notification, you can answer by clicking the notification.
Packing List
Outdoor Phone part
Indoor Monitor part
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>