MP Global QuietWalk LV Laminate Flooring Underlayment Instructions

MP Global QuietWalk LV Laminate Flooring Underlayment

Product Information

The product is called QuietWalk and it is designed to provide sound reduction and moisture protection for laminate and engineered wood flooring installations. It is a high-quality underlayment that creates a cushioning layer between the subfloor and the flooring, resulting in a quieter and more comfortable living space.

Features:

• Sound Reduction: QuietWalk minimizes noise transmission by absorbing sound vibrations.
• Moisture Protection: It acts as a moisture barrier, preventing water damage to the flooring.
• Cushioning: The underlayment provides a comfortable walking surface and helps to reduce foot fatigue.

Installation Methods:
QuietWalk can be installed using various methods depending on the requirements of your specific flooring project. The following installation methods are recommended:

1. Floating Installation: This method involves laying the QuietWalk underlayment directly on the subfloor without any adhesives. The flooring is then installed on top of the underlayment.

2. Nailed/Stapled Installation: In this method, the QuietWalk underlayment is first attached to the subfloor using nails or staples. The flooring is then nailed or stapled on top of the
   underlayment.

3. Glue-Down Installation: For this method, an adhesive is used to secure the QuietWalk underlayment to the subfloor. The flooring is then glued down on top of the underlayment.

Product Usage Instructions

To ensure proper installation and optimal performance, please follow these usage instructions:

1. Prepare the Subfloor: Ensure that the subfloor is clean, dry, and level before installing the QuietWalk underlayment.
2. Unroll the Underlayment : Roll out the QuietWalk underlayment across the entire installation area, overlapping the seams by a minimum of 2 inches.
3. Secure the Underlayment: Depending on the chosen installation method, either use adhesive, nails, or staples to secure the QuietWalk underlayment to the subfloor. Follow the manufacturer’s instructions for the chosen installation method.
4. Install the Flooring: Once the underlayment is securely in place, proceed with installing your laminate or engineered wood flooring according to the manufacturer’s instructions.
5. Trim Excess Underlayment: After the flooring installation is complete, trim any excess QuietWalk underlayment using a utility knife or scissors.

For more detailed installation guidance, it is recommended to refer to the installation videos and tips available at quietwalk.com/lv- install. Additionally, please review the Limited Lifetime Warranty information provided at quietwalk.com/lv- warranty
for warranty details and terms.

• For use under vinyl plank, laminate, solid and engineered hardwood flooring.
• Enhanced performance for attached pad flooring.

Sound control

Sound Reduction
Recycled fibers absorb sound and keep it from traveling to other rooms.

Moisture Protection

quietwalk.com/driwick

DURABILITY PRODUCT DETAILS

• DIMENSIONS 1.4 mm thick x 3 ft wide × 33.3 ft long
• SOUND INSULATION |IC 70 STC 62 Delta lIC 28
• MOISTURE VAPOR EMISSIONS .12 LBS / 1000 SQ FT / 24 HOURS
• THERMAL INSULATION R-Value 0.528
• COMPRESSION STRENGTH 64.58 PSI

SAFETY & ENVIRONMENT GREENGUARD

• Odorless, No VOCs ULCOM/GG UL 2818 GOLD
• Antimicrobial Protection
• Approved for use with radiant heat systems
• Made from 94% recycled materials
• LEED compliant

INSTALLATION INSTRUCTIONS

• All wood and concrete subfloors must be flat within 1/8″ over a 6’span, or 3/16″ over a 10’span.
• All areas must be checked prior to installation.

View Installation Videos and Tips at quietwalk.com/lv- install View Limited Lifetime Warranty at quietwalk.com/lv-warranty

GENERAL INFORMATION

• Product may be installed over:
  • QuietWalk LV be used over any subfloor approved by the finished floor covering manufacturer . Suitable with Radiant Heat Systems
• Recommended Uses :
  • Residential applications on all grade levels
  • Floating Vinyl, Laminate and Engineered Wood Floors
  • Commercial double glue applications (4mm or thicker flooring)
  • Interior use in dry, heated areas
• Subfloor and Preparation:
  • All subfloors must be flat, clean, smooth and dry
  • Sand any rough surfaces and/or uneven joists
  • Fill any cracks on concrete or panel joints wider than 1/8″ using a recommended patch/ leveling product

INSTALLATION METHODS

Floating Floor Installation:

• Be sure the subfloor is clean, smooth and free of dust and debris
• Unroll the QuietWalk Luxury Vinyl Underlayment and flip it over so the film side is up (felt side down)
• Make sure that underlayment seams run perpendicular (at right angle) to the long dimension of the planks.
• Underlayment must be positioned with a minimum 4″ separation between seams of underlayment and seams of finished flooring products
• Trim the perimeter edges of the QuietWalk Luxury Vinyl Underlayment ¼” from the wall
• Butt seams together and seal using the factory attached lip and tape system.
• For seams that do not have the lip and tape feature, use a good quality single faced tape to seal the seams
• Install the floor covering product according to the manufacturer’s instructions

Double-Glued Installation :

• Double Glue Down installations are approved with flooring that is a minimum thickness of 4mm.
• Be sure the subfloor is clean and free of dust and debris
• Unroll the first drop of QuietWalk Luxury Vinyl Underlayment and flip it over so the film side is up (felt side down)
• Make sure that underlayment seams run perpendicular (at right angle) to the long dimension of the planks Remove the lip portion of the lip and tape system with a utility knife and discard Remove the tape strip cover portion of the lip and tape system and discard
• Trim to fit the QuietWalk Luxury Vinyl Underlayment into the target areas. Move the trimmed-to-fit underlayment to the side to apply the adhesive Apply a recommended pressure sensitive adhesive using the flooring manufacturer recommended trowel Once the adhesive has flashed (dried to a tacky touch) place the trimmed-to-fit underlayment into the adhesive
• Butt seams together and apply 2″ wide clear packaging tape centered over the seam Roll the adhered QuietWalk Luxury Vinyl Underlayment with a 100 lb flooring roller
• Mark starting lines on Underlayment for placement of finished flooring product Apply a recommended pressure sensitive adhesive using the flooring manufacturer recommended trowel Once the adhesive has flashed (dried to a tacky touch) you can begin flooring installation according to the manufacturers recommendations
• Make sure the staggered end joints fall at least 2″ away from the underlayment seams
• Maintain a minimum expansion gap of ¼” around the perimeter of the room
• Follow flooring manufacturer recommendations for installing transitions in large span applications and doorwavs
• Roll the finished floor with a 100 lb flooring roller
• Be sure not to slide flooring into position which could potentially displace adhesive

Mechanically Fastened Hardwood Floors

• Unroll the underlayment and ensure vapor side is up and fibers are to the subfloor.
• Install underlayment in opposite direction to the flooring material. You can tape the seams but it is not necessary.
• Install the hardwood per manufactures written instructions, using their recommended fastening materials.

Trim and Molding:

• All finish trim and transition moldings must be installed without binding or restricting the free movement of the above finished flooring products

References

• Loading

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>