iArmor IA-S058H 6.5 Inch Stainless Steel Running Boards Installation Guide
- May 15, 2024
- iArmor
Table of Contents
iArmor IA-S058H 6.5 Inch Stainless Steel Running Boards
Product Specifications:
- Part Number: IA-S058H
- Mounting Type: Rocker Panel Mount
- Installation: No drilling/trimming required
Torque Values:
| Fastener Size | Tightening Torque (ft-lbs) |
|---|---|
| 6mm | 6-7 |
| 8mm | 16-18 |
| 10mm | 31-32 |
| 12mm | 56-58 |
| 14mm | 92-94 |
Before Installation:
- Remove all contents from the box and verify all parts are present.
- Read the instructions carefully before starting the installation.
- Assistance is recommended for installation.
Part List
- Driver Front Mounting Bracket (DFM)
- Passenger Front Mounting Bracket (PFM)
- Driver Center Mounting Bracket (DCM)
- Driver Rear Mounting Bracket (DRM)
- Passenger Center Mounting Bracket (PCM)
- Passenger Rear Mounting Bracket (PRM)
- Driver Side Step Bar
Hardware Package A (For Bracket Installation):
- 6 U Brackets
- 12 M8X1.25-25mm Hex Bolts
- 12 M8 Large Flat Washers
- 12 M8 Lock Washers
Hardware Package B (For Step Bar Installation):
- 6 M8X1.25-55mm Carriage Bolts
- 6 M8 Lock Washers
- 6 M8 Large Flat Washers
- 6 M8 Hex Nuts
Frequently Asked Questions (FAQ):
-
Q: Can I install the product without professional help?
A: While we recommend professional installation for the best results, the instructions provided can guide you through the process. However, we are not responsible for any damage caused by self-installation. -
Q: Are all necessary parts included in the package?
A: Yes, please ensure you have verified that all parts listed in the manual are present before starting the installation.
iArmor® by APS
BEFORE INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED. THANK YOU FOR CHOOSING OUR PRODUCT!
- ROCKER PANEL MOUNT
- NO DRILLING / TRIMMING REQUIRED
Torque Value
| Fastener Size | Tightening Torque (ft-lbs) | Required |
|---|---|---|
| 6mm | 6-7 | X |
| 8mm | 16-18 | √ |
| 10mm | 31-32 | X |
| 12mm | 56-58 | X |
| 14mm | 92-94 | X |
Customer Support:
info@iarmorauto.com
The instructions here is for your reference only. We strongly
recommend the professional installer for best result. We are not responsible
for any damage caused by the installation.
-
STEP 1
Starting on the driver-side front of the vehicle, remove the existing (2) factory bolts, (or plastic plugs) (Fig 1). This will be the mounting location for the Driver Front Mounting Bracket (DFM).
-
STEP 2
Select the Driver Front Mounting Bracket (DFM). Attach the Bracket to the vehicle using the included (2) M8X1.25-25mm Hex Bolts, (2) M8 Lock Washers and (2) M8 Large Flat Wash-ers, (Fig 2). Do not fully tighten hardware at this time.
-
STEP 3
Move along the side panel to the next mounting location closest to the front Bracket, (Fig 3). Repeat Steps 1 & 2 to install the Driver Center Mounting Bracket (DCM), (Fig 4).
-
STEP 4
Next, move to the last mounting location at the back of the cab. Select the Driver Rear Mounting Bracket (DRM). Repeat Steps 2 & 3 to install the rear Bracket (Fig 5). -
STEP 5
Once all (3) driver side mounting brackets are installed, select and attach the Driver Side Step Bar onto the Mounting Brackets with (3) U Brackets, (3) M8X1.25-55mm Carriage Bolts, (3) M8 Large Flat Washers, (3) M8 Lock Washers and (3) M8X1.25 Hex Nuts (Fig 6). Do not fully tighten hardware at this time. -
STEP 6
Properly level and adjust the Step Bar and fully tighten all hardware. -
STEP 7
Move to the passenger side of the vehicle. Repeat Steps 1-6 to install passenger side step bar.
Installation completed.
Attention
Do periodic inspections to the installation to make sure that all hardware is
secure and tight.
In order to protect your bars/boards, please use mild soap/non-abrasive
products for cleaning only.
Customer Support: info@iarmorauto.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>