Delta-5CH-550L Steamscape Deluxe System Instruction Manual

Delta-5CH-550L Steamscape Deluxe System

Read all instructions prior to installation.

CAUTION

Failure to read these instructions prior to installation may result in personal injury, property damage, or product failure. Manufacturer assumes no responsibility for product failure due to improper installation.

You may need

Rough In Steam Line (not supplied)

Prior to steam head installation, Install rough plumbing line to desired location. The steam head must be installed to a ¾” NPT copper or brass pipe; do NOT use black iron or galvanized pipe, it will rust and discolor the steam bath wall. Do NOT use plastic supply pipes or fittings.

NOTE : Supply elbow and steam supply pipe MUST BE SECURELY ANCHORED to ridged blocking.
The steam head location should be 12” to 18” above the shower floor or 6” above the rim of the bathtub, as far from the seating area as possible.

Steam Head Installation

1. Make sure the 3/4” nipple protrudes beyond the tile ¼” to ½” (6-12 mm).

2. Keep opening in finished wall close as possible to pipe nipple with no more than 1/2” gap.
   IMPORTANT: If the nipple protrudes beyond ½” the O-ring will not make a proper seal and the nipple will have to be adjusted.

3.  Wrap the threads of the nipple with plumber’s tape or use pipe sealant.

4.  Make sure the steam head will line up in the upright position when tightened. The steam head should only be firmly hand tight. Using a wrench on the head may damage it. Screw the steam head on to the nipple and see how it lines up. Once a proper alignment is made remove the steam head.

NOTE: The steam head has been designed with a 360 degree dispersion of steam to improve steam circulation and to minimize the hotspots created with the traditional steam heads. For maximum comfort the steam head should always be located as far from the seating area as possible. Should the location of the steam head necessitate blocking the steam from a particular direction to improve bather comfort, the supplied deflector plate can be added to any of the three sides shown to help divert the steam away from the bather. The deflector is attached to the back side of the head before installation with 2 stainless steel screws provided. (See Option Installation, Deflector section on next page).

NOTE: If necessary the head can be repositioned by disassembling the hub from the cover and selecting one of the two alternate positions.

1. Re-apply sealant tape if necessary.
2. Place a bead of silicone around the pipe, sealing the pipe to the wall.
3. Place a bead of silicone around the back outer edge of the back plate.
4. Center and square the back plate over the nipple. While holding the head in place, attach the nipple by hand tightening the screws to the head.
5. Adjust the back plate and head to line up squarely. Remove any excess silicone with rubbing alcohol.

Optional Installation

IMPORTANT: A silicone boot is provided and should be installed to protect against accidental contact with the hot surface temperature of the steam head, which can reach approximately 212° during operation.

If needed to improve bather comfort the included optional steam deflector can be installed to block the flow of steam from any of the shown sides of the steam head.

Limited Warranty

Limited Warranty on Delta® Steam Bath and Steam Shower Products

Residential Steam Bath Generators: Delta Faucet Company (“DFC”) warrants to the original consumer purchaser that the parts (except for electronic parts) of its residential steam bath generator purchased from authorized Delta sellers will be free from defects in materials and workmanship for as long as the original consumer purchaser owns the home in which the steam bath was originally installed. This lifetime limited warranty does not apply to residential steam bath generators that are used in commercial applications (as defined herein).
Residential Electronic Parts, Controls, Spa Options and Accessories: DFC warrants to the original consumer purchaser that the electronic parts of its steam bath generator and its controls, spa options and accessories purchased from authorized Delta sellers will be free from defects in materials and workmanship for a period of two (2) years from the date that the product is received by the original consumer purchaser or their authorized representative (installation contractor, etc.). This two-year limited warranty does not apply to controls, spa options, electronic parts and accessories that are used in commercial applications (as defined herein).
Commercial Warranty: For the purposes of this warranty the term “commercial application” refers to installation in any setting in which the product is not being used for personal household use, including but not limited to hospitality applications, day spas, short-term and long-term rentals and gyms.
DFC warrants that the parts (including electronic parts) of its steam bath generators (including steam bath generators with model numbers beginning with 5COM, which are intended solely for heavy commercial use), equipment, controls, electronic parts, spa options and accessories purchased from authorized Delta sellers and used in a commercial application will be free from defects in materials and workmanship for a period of one (1) year from the date that the product is received by the original purchaser or their authorized representative (installation contractor, etc.).
What We Will Do: DFC will, at its option, repair or replace, free of charge, any part that proves defective in material and/or workmanship under normal installation, use and service during the applicable warranty period as stated above.
DFC may elect to refund the purchase price. Replacement parts are subject to availability and may differ from those originally supplied.
For residential applications, two (2) years following the date that the product was received by the original consumer purchaser or their authorized representative (installation contractor, etc.), and with prior approval by DFC, DFC will pay for labor for repair/replacement associated with warranty coverage. Thereafter, DFC will not pay for labor associated with removal/repair/replacement of products covered by this warranty.
For commercial applications, DFC will, with prior approval by DFC, pay for labor associated with warranty coverage for ninety (90) days from the date that the product is received by the original purchaser or their authorized representative (installation contractor, etc.). Thereafter, DFC will not pay for labor associated with removal/repair/replacement of products covered by this warranty. These are the consumer’s exclusive remedies. What Is Not Covered: Because DFC is unable to control the quality of Delta products sold by unauthorized sellers, unless otherwise prohibited by law, this warranty does not cover Delta products purchased from unauthorized sellers.
This warranty does not cover damage caused by improper or negligent installation or use. Provided that DFC is paying Applicable to products purchased and installed in the USA and Canada the cost of the labor under the terms above, this warranty does not cover repairs attempted by any person other than an authorized DFC agent and shall be limited to the repair or replacement of defective parts by DFC or its authorized agent.

This warranty is void if any of the following should occur:

• The use of the product for an unintended application, including the commercial application of a product that is not intended for commercial use.
• Failure to follow instructions, including care, cleaning and usage instructions, provided in the product’s owner’s manual.
• The product’s serial number has been altered or removed.
• The product is modified in any manner which DFC concludes, after its inspection, affects the reliability of the product.
• The product has been improperly repaired by anyone not specifically designated or authorized by DFC.
• The product is damaged because it is not operated or installed in accordance with supplied instructions.
• The product is installed outdoors.
• The product is installed in a moist and/or humid area with unconditioned air or temperatures that exceed 104 degrees Fahrenheit.
• The product is damaged due to freezing.
• The product is damaged by acts of God.

How to Make a Warranty Claim: To obtain warranty repair or replacement, contact DFC at: 800-394-6478 or steamprodserv@deltafaucet.com to receive an RGA# (Return Goods Authorization number) which must be on the carton that is returned via UPS Ground or equivalent. Proof of purchase (original sales receipt showing purchase date) identifying the model and serial number and documentation of the date of receipt of the product by the original purchaser or their authorized representative (installation contractor, etc.) must accompany all warranty claims.
Limitation on Duration of Implied Warranties: Please note that some states/provinces (including Quebec) do not allow limitations on how long an implied warranty lasts, so the below limitations may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO THE STATUTORY PERIOD OR THE DURATION OF THIS WARRANTY, WHICHEVER IS SHORTER.
Limitation of Special, Incidental or Consequential Damages: Please note that some states/provinces (including Quebec) do not allow the exclusion or limitation of special, incidental or consequential damages, so the below limitations and exclusions may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY DOES NOT COVER, AND DFC SHALL NOT BE LIABLE FOR, ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES WHETHER ARISING OUT OF BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, BREACH OF CONTRACT, TORT, OR OTHERWISE.
Additional Rights: This warranty gives you specific legal rights, and you may also have other rights which vary from state/province to state/province. This is DFC’s exclusive written warranty and the warranty is not transferable.

You May Need

Limited Warranty on Delta® Steam Bath and Steam Products

Applicable to products purchased and installed in the USA and Canada

Residential Steam Bath Generators: Delta Faucet Company (“DFC”) warrants to the original consumer purchaser that the parts (except for electronic parts) of its residential steam bath generator purchased from authorized Delta sellers will be free from defects in materials and workmanship for as long as the original consumer purchaser owns the home in which the steam bath was originally installed. This lifetime limited warranty does not apply to residential steam bath generators that are used in commercial applications (as defined herein).
Residential Electronic Parts, Controls, Spa Options and Accessories: DFC warrants to the original consumer purchaser that the electronic parts of its steam bath generator and its controls, spa options and accessories purchased from authorized Delta sellers will be free from defects in materials and workmanship for a period of two (2) years from the date that the product is received by the original consumer purchaser or their authorized representative (installation contractor, etc.). This two-year limited warranty does not apply to controls, spa options, electronic parts and accessories that are used in commercial applications (as defined herein). Commercial Warranty: For the purposes of this warranty the term “commercial application” refers to installation in any setting in which the product is not being used for personal household use, including but not limited to hospitality applications, day spas, short-term and long-term rentals and gyms.
DFC warrants that the parts (including electronic parts) of its steam bath generators (including steam bath generators with model numbers beginning with 5COM, which are intended solely for heavy commercial use), equipment, controls, electronic parts, spa options and accessories purchased from authorized Delta sellers and used in a commercial application will be free from defects in materials and workmanship for a period of one (1) year from the date that the product is received by the original purchaser or tier authorized representative (installation contractor, etc.).
What We Will Do: DFC will, at its option, repair or replace, free of charge, any part that proves defective in material and/or workmanship under normal installation, use and service during the applicable warranty period as stated above. DFC may elect to refund the purchase price. Replacement parts are subject to availability and may differ from those originally supplied.
For residential applications, two (2) years following the date that the product was received by the original consumer purchaser or their authorized representative (installation contractor, etc.), and with prior approval by DFC, DFC will pay for labor for repair/replacement associated with warranty coverage. Thereafter, DFC will not pay for labor associated with removal/repair/replacement of products covered by this warranty.
For commercial applications, DFC will, with prior approval by DFC, pay for labor associated with warranty coverage for ninety (90) days from the date that the product is received by the original purchaser or their authorized representative (installation contractor, etc.). Thereafter, DFC will not pay for labor associated with removal/repair/replacement of products covered by this warranty. These are the consumer’s exclusive remedies.
What Is Not Covered: Because DFC is unable to control the quality of Delta products sold by unauthorized sellers, unless otherwise prohibited by law, this warranty does not cover Delta products purchased from unauthorized sellers.
This warranty does not cover damage caused by improper or negligent installation or use. Provided that DFC is paying the cost of the labor under the terms above, this warranty does not cover repairs attempted by any person other than an authorized DFC agent and shall be limited to the repair or replacement of defective parts by DFC or its authorized agent.

This warranty is void if any of the following should occur:

• The use of the product for an unintended application, including the commercial application of a product that is not intended for commercial use.
• Failure to follow instructions, including care, cleaning and usage instructions, provided in the product’s owner’s manual.
• The product’s serial number has been altered or removed.
• The product is modified in any manner which DFC concludes, after its inspection, affects the reliability of the product.
• The product has been improperly repaired by anyone not specifically designated or authorized by DFC.
• The product is damaged because it is not operated or installed in accordance with supplied instructions.
• The product is installed outdoors.
• The product is installed in a moist and/or humid area with unconditioned air or temperatures that exceed 104 degrees Fahrenheit.
• The product is damaged due to freezing.
• The product is damaged by acts of God.

How to Make a Warranty Claim: To obtain warranty repair or replacement, contact DFC at: 800-394-6478 or steam- prodserv@deltafaucet.com
to receive an RGA# (Return Goods Authorization number) which must be on the carton that is returned via UPS Ground or equivalent. Proof of purchase (original sales receipt showing purchase date) identifying the model and serial number and documentation of the date of receipt of the product by the original purchaser or their authorized representative (installation contractor, etc.) must accompany all warranty claims. Limitation on Duration of Implied Warranties: Please note that some states/provinces (including Quebec) do not allow limitations on how long an implied warranty lasts, so the below limitations may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO THE STATUTORY PERIOD OR THE DURATION OF THIS WARRANTY, WHICHEVER IS SHORTER.

Limitation of Special, Incidental or Consequential Damages: Please note that some states/provinces (including Quebec) do not allow the exclusion or limitation of special, incidental or consequential damages, so the below limitations and exclusions may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY DOES NOT COVER, AND DFC SHALL NOT BE LIABLE FOR, ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES WHETHER ARISING OUT OF BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, BREACH OF CONTRACT, TORT, OR OTHERWISE.

Additional Rights: This warranty gives you specific legal rights, and you may also have other rights which vary from state/province to state/ province. This is DFC’s exclusive written warranty and the warranty is not transferable.

This device complies with part 15 of the FCC Rules. This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s) and operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an output on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Pursuant to FCC 15.21 of the FCC rules, changes not expressly approved by Delta Faucet Co. might cause harmful interference and void the FCC authorization to operate this product.

Cleaning and Care

Interface MUST be installed inside the steam room for proper operation of the system. Use a damp cloth and mild soap. Do NOT use abrasive cleaners which might scratch the surface or the base of the interface.

The 5CN-550L, 5CH-550L & 5CB-550L digital interfaces will only function with 5GE SteamScape series generators.

Pre-Installation – Interface Location

The 5CN-550L, 5CH-550L & 5CB-550L digital interfaces must be installed inside the steam room and away from the steam head (opposite wall preferred). For convenience the recommended height from the floor is four feet. Provide a 2 3/4” hole in the wall at this location (see Figure 1).

Electrical Rough-in

Locate the multi-conductor cable (supplied with steam generator). Carefully route this interface cable from the steam generator to the 5CN-550L, 5CH-550L or 5CB-550L digital interface located inside the steam room (see Figure 1). Route this interface cable through a ¾” conduit to protect the cable from damage and to facilitate replacement if necessary.

Interface and Cable Installation

1. Locate the previously installed cable and black plastic strain relief clamp. Locate the knockout on the steam generator for the interface cable (see Figure 2).
2. Place strain relief around cable about seven inches from the end and insert into the hole.
3. Remove the protective cap from the multi-conductor cable plug. Connect the cable to the modular jack.
4. Close and secure the steam generator cover.
5. Locate the modular jack at the female coupler on back of the 5CN-550L, 5CH-550L or 5CB-550L digital interface. Check that the orientation of the plug properly aligns with the jack. A snap will indicate the plug is installed correctly (see Figure 3).

Test the interface for operation before continuing on to the next step.

6. Peel adhesive liner from back of the interface. Apply silicone (supplied) into around the back edge of the interface to form a watertight seal (see Figure 3).
7. Apply the interface to the wall. Press firmly and hold for a few seconds. Wipe the excess silicone from around the interface.

IMPORTANT: The 5CN-550L, 5CH-550L & 5CB-550L digital interfaces have built in temperature sensors and therefore MUST be installed inside the steam room.
IMPORTANT: The adhesive on the back of the 5CN-550L, 5CH-550L & 5CB-550L digital interfaces will NOT seal this interface. It is the responsibility of the installer to seal this interface to the wall with the supplied silicone. Water damage to the interface is not covered by the warranty.
IMPORTANT: 5CN-550L, 5CH-550L & 5CB-550L digital interfaces cable MUST plug directly into the steam generator. Do NOT plug this interface into the optional 5SP-MU audio speaker system.
Temperature settings: 60ºF min to 125ºF max Maximum Time setting: 60 Minutes

Interface Operation

The 5CN-550L, 5CH-550L & 5CB-550L digital interfaces have built-in temperature sensors and therefore MUST be installed inside the steam room. This interface is compatible to work with 5GE steam generators and the optional audio speaker system.

Power on the Digital Interface

Congratulations on the purchase of the 5CN-550L, 5CH-550L or 5CB-550L series digital interface

• After powering on the interface you will experience a blank screen for approximately 60 seconds.

Before You Install

• This interface is pre-configured to be installed in landscape orientation. If you prefer to install in portrait mode, please see the following steps in this section. Otherwise, these steps can be disregarded.

• To rotate the screen press the SETTING “gear” icon in the top left corner on main screen.
  

• In the MAIN SETTINGS, go to DISPLAY.
  

• Then ORIENTATION.

• Select the desired orientation for your Interface.
  The system will then restart.
  

Connect to WiFi

• If it is the first time powering on the digital interface, you will get the Terms of Use, then Privacy policy and you will need to check the ACCEPT box in order to proceed.
  

• Then you will be able to select and sign in to your desired Wi-Fi network.
  

• After the desired network has been selected, you will be prompted to enter a password.
  

Audio Speaker System Settings

• If the speaker system is installed, you will see the AUDIO Icon. This is where you would play music without starting a Steam Preset.
  

• In the AUDIO screen you may select the source of your music by pressing A, B, or Bluetooth.

• Skip Forward, Pause/ Play and Skip Back work when the system is paired with Bluetooth, but does not support audio use with the A or B inputs.

• Volume, Balance, Bass, and Treble are all adjusted with the plus and minus icons by selecting the feature.

• Press the Return icon when you are done with the music settings.
  

Main Settings

• The SETTINGS screen gives you access to make several different configuration changes to customize your overall experience.
  

Clock Settings

• Press the CLOCK icon to adjust the clock settings.
• The time format may also be changed.
  

About Information

• Press the ABOUT icon to see any devices connected to the system.
• This screen is for troubleshooting purposes only. Listed are all the possible connected devices and the version numbers will show if they are communicating with the 5CN-550L, 5CH-550L or 5CB-550L interface.
• Press the RETURN icon to return to the Settings screen.
  

Temperature Limit Settings

• You may increase or decrease the maximum steam temperature from the TEMPERATURE LIMIT settings screen.
  

Bluetooth Settings

• If you have the audio speaker system installed, you will need to turn the BLUETOOTH feature on to stream audio from your mobile device.
• Also take note of the DELTA AUDIO bluetooth name that will be shown on your digital interface.
• You will look for that name on your mobile device when pairing.
  

Language Settings

• Adjust your prefered language setting here.
  

Wi-Fi Settings

• From the settings screen, press the Wi-Fi icon.
• Check the ADVANCED SETTINGS box to get access to more granular settings to your Wi-Fi network.
• Press the Wi-Fi Settings icon to connect the interface to Wi-Fi.
  

Advanced Settings

• If you have downloaded the DFC@Home smart phone app, you can pair your mobile phone with the interface.
  

• If you would like to reset your interface to factory default settings, you may do so via the system reset feature.
  Note: All saved settings will be deleted via this action.
  

Firmware Update Settings

• The display screen will show “FIRMWARE UPDATE UPDATING”. Do NOT press any icons while update is in process.
• The interface MUST be connected to Wi-Fi to update Firmware.
  

Starting a Preset

• Select the STEAM icon at the bottom of the screen.

• Upon selection, the profile menu will open allowing you to access the user presets within each profile.
  

• Within each preset are the options to adjust the TEMPERATURE, TIME LEFT, and DURATION of that preset.

• The TEMPERATURE setting allows you to make adjustments to the temperature for the Preset.
  Note: This is different from the maximum temperature settings referenced.
  

• TIME LEFT gives you the ability to add more time to the active preset. You can increase this to a maximum of 60 minutes.
  

• DURATION gives you the ability to adjust the time configured in the preset.

• TIME LEFT allows you to increase or decrease the time of the active steam session only
  

The Post Preset Experience

• At the end of your steam session, your steam will stop, but your audio will continue if you have the audio speaker system installed with your system.
• When you press END you will be prompted to save any adjustments you made to your preset.
  

Mobile App Settings

• Download the DFC@Home mobile app from the Apple® App Store (iOS users) or Google® Play Store (Android users) for additional functionality and to finalize setup.
• The DFC@Home mobile app allows for additional profile and preset customization and remote access of your steam shower.
• The 5CN-550L, 5CH-550L or 5CB-550L interface must remain connected to Wi-Fi to ensure access to the DFC@Home mobile app.
  

Get the mobile app.

Voice Assistant Settings

• You will need to have an account setup with either service.
• The Amazon Alexa or Google Home mobile app must be installed on your phone.
• You must have an Amazon Alexa or Google home compatible speaker.
• The DFC@Home mobile app will provide instructions and will guide you through the setup process.

Customer Support

Register Online
Regístrese en línea
S’enregistrer en ligne
www.deltafaucet.com/service-parts/product- registration

To reference replacement parts and access additional technical documents and product info, visit www.deltafaucet.com/service- parts

1-800-394-6478 www.deltafaucet.com /service-parts/contact-us/

Register Online
www.deltafaucet.com/registerme

References

• deltafaucet.com
• deltafaucet.com
• deltafaucet.com/
• Register Your Delta Faucet Product | Delta Faucet
• deltafaucet.com/service-parts
• Delta Faucet Contact Us Center & Support Resources

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>