SAVANT PS20-BATT-20KWH LFP Battery System User Guide

June 17, 2024
SAVANT

SAVANT PS20-BATT-20KWH LFP Battery System

SAVANT-PS20-BATT-20KWH-LFP-Battery-System-PRODUCT

Product Information

Specifications

  • Inverter Power: 12.5 kW
  • Battery Capacity: 52 Ah / 20 kWh
  • Maximum Passthrough Per Inverter: 100A
  • Height: 85.4 in (216.92 cm)
  • Length: 25.6 inches (65.02 cm)
  • Depth: 12.2 inch (30.988 cm)
  • Weight: 600 lbs (272.15 kg)
  • Temperature: NC1 COM2, NC2 COM, GPS, USB4, NO1 COM2 NO2, LH, TR RS232, DC 12V, DC 12V, PS G C-LED, GBA UPCS, DC 12V, RS232, RS232, BCMS, NETWORK USB2, USB3, SD RESET 4G LTE, C-LED, RS485-4 UPCS RS485-1 DC V12, GRID L1 N L2, LOAD L1 N L2, GEN L1 N L2
  • Humidity: 0% to 95% Relative Humidity (noncondensing)
  • Altitude: Less than 9842 ft
  • Rating: NEMA4X

Product Usage Instructions

Box Contents

  • (1) Savant Power Inverter (PS-INV-12.5KW-100A-XX)
  • (8) Power Storage 20 Battery (PS20-BATT-20KWH)
  • (1) Savant Power Director
  • (1) Battery Crate (8 x Modules)
  • (1) Conduit Nipple Kit
  • (1) Mounting & Installation Kit
  • (4) M5x12 Screws
  • (4) M5x10 Screws
  • (4) M10 Expansion Screws
  • (4) M6 Expansion Anchor Screw

Inverter Front Panel

  • A – Inverter Status LEDs
  • B – Inverter Front Panel
  • C – ON/OFF Button
  • D – Grid Switch
  • E – Conduit Knock-outs
  • F – Antennas (Wi-Fi, GPS, 4G Main, and 4G DIV Antennas)

Inverter I/O Ports

  • A – Network Status LED
  • B – Network RJ45 connection for wired internet connection
  • C – USB Ports (Used for local software updating)
  • D – SD (Enables local data collection without internet connection)
  • E – Reset (Reset button to reset inverter status)
  • F – CLED (Power input for LEDs)
  • G – GPIO Ports
  • H – BCMS (Battery Monitor System Communication Port)
  • I – RS-485 Port

FAQ

How much power can the Savant Power Storage 20 Inverter provide?

  • The Savant Power Storage 20 Inverter can provide a maximum power of 12.5 kW.

What is the battery capacity of the Power Storage 20?

  • The Power Storage 20 has a battery capacity of 52 Ah / 20 kWh.

What is the maximum passthrough per inverter?

  • The maximum passthrough per inverter is 100A.

What are the environmental specifications for the product?

  • The product can operate within a temperature range specified by the following components: NC1 COM2, NC2 COM, GPS, USB4, NO1 COM2 NO2, LH, TR RS232, DC 12V, DC 12V, PS G C-LED, GBA UPCS, DC 12V, RS232, RS232, BCMS, NETWORK USB2, USB3, SD RESET 4G LTE, C-LED, RS485-4 UPCS RS485-1 DC V12, GRID L1 N L2, LOAD L1 N L2, GEN L1 N L2. The product is also designed to operate in a humidity range of 0% to 95% relative humidity (noncondensing).
  • The product should be used at an altitude of less than 9842 ft and have a NEMA4X rating.

What are the dimensions and weight of the product?

  • The product has a height of 85.4 in (216.92 cm), a length of 25.6 inches (65.02 cm), and a depth of 12.2 inches (30.988 cm). The weight of the product is 600 lbs (272.15 kg).

Box Contents

  • (1) Savant Power Inverter (PS-INV-12.5KW-100A-XX)
  • (8) Power Storage 20 Battery (PS20-BATT-20KWH)
  • (1) Savant Power Director
  • (1) Battery Crate (8 x Modules)
  • (1) Conduit Nipple Kit
  • (1 ) Mounting & Installation Kit
  • (4) M5x12 Screws
  • (4) M5x10 Screws
  • (4 ) M10 Expansion Screws
  • (4) M6 Expansion Anchor Screw

Specifications

SAVANT-PS20-BATT-20KWH-LFP-Battery-System-FIG-1

Inverter Front Panel Right Panel Left Panel

Descriptions

SAVANT-PS20-BATT-20KWH-LFP-Battery-System-FIG-3

Inverter I/O Ports

Front Input/Outputs

Inverter Status LEDs

Status LEDs & Inverter StatesSAVANT-PS20-BATT-20KWH-LFP-Battery-System-
FIG-6

Battery Status Panel

SAVANT-PS20-BATT-20KWH-LFP-Battery-System-FIG-7

Battery Status Panel I/O & Status LEDs

SAVANT-PS20-BATT-20KWH-LFP-Battery-System-FIG-8

Battery Access PanelSAVANT-PS20-BATT-20KWH-LFP-Battery-System-
FIG-9

Battery Status Panel I/O & Status LEDs

Bracket Installation

  1. Open the battery enclosure with a PH2 Philips screwdriver and remove the accessories kit.
  2. Assemble the bracket as shown using M5x12 screws.
  3. Attach the bracket to the back side of the battery system with M5x12 machine screws. Tighten to 3 N·m (26.55 lb-in) torque.
  4. Drill a 0.47 in (12mm) hole with a 2.76 in (70mm) depth into the floor. Embed the anchor expansion bolts and affix the cabinet to the ground.SAVANT-PS20-BATT-20KWH-LFP-Battery-System-FIG-12
  5. Install the bracket on the wall with M6x50 tapping screws.
    • IMPORTANT NOTES:
    • When installing it on a concrete wall, properly drill into the wall with M6x50 expansion anchor screws.
    • If Savant Power Inverter is installed separately from the battery system, install the bracket on a surface capable of supporting its weight using an M6x50 tapping screw.
    • Then hang the Savant Power inverter on the bracket, and fasten it with M4x16 screws.
    • Inverter Installation
  6. Remove the battery seal cap marked BAT/COM on the bottom left of the Savant Power Inverter.
  7. Remove the Battery Status panel side communication cable panel.
  8. Hang the inverter on the bracket.
  9. Fasten the Savant Power Inverter and the bracket with M5x12 machine screws. (Torque: 3 N·m).
  10. Fasten Savant Power Inverter and the battery cabinet with conduit and screw kit, as shown.SAVANT-PS20-BATT-20KWH-LFP-Battery-System-FIG-14
  11. Gently plug in each battery module from the bottom up.
    • Fasten the modules on both sides using M4x8 screws (Torque: 1.2 N·m).
    • NOTE: Mark number 1~8 on the labels of each battery module before installation and plug them into the cabinet in reverse numerical order.
    • Always keep batteries ordered as they are first installed.

Wiring

  1. Connect the battery system to the Savant Power Inverter with ground wire.
  2. Make the REF, BAT-, and BAT+ connections from the inverter through the conduit to the corresponding connections on the battery access panel through the conduit.
  3. Connect the DC 12V wire between the inverter and the battery battery access panel.
  4. Connect the BCMS port of the Savant Power Inverter to the CANBUS connection of the Battery Status Panel.
  5. Make all connections between the inverter and the electrical system. Generator, and Load connections. For more information, see the Savant Power Storage 20 Deployment Guide.
  6. (Optional) Connect Savant Power Storage 20 to the photovoltaic array.
  7. Connect Savant Power Storage 20 to the same network switch as the Power Director or the network port of the Power Director itself using a CAT5 or higher Ethernet cable.

More Information

  • To continue deployment and configure the Savant Power Storage 20, see the following documentation.

Savant Power Storage App Setup GuideSAVANT-PS20-BATT-20KWH-LFP-Battery-
System-FIG-21

Savant Power Storage 20 Installation Guide

  • Copyright © 2023 Savant Systems, Inc
  • 090523 009-2383-00
  • Savant Power Storage [100A] QRG
  • 45 Perseverance Way, Hyannis MA 02601 www.savant.com
  • 508.683.2500

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SAVANT User Manuals

Related Manuals