MeTra 99-7807 Car Audio Accessory Installation Guide

June 6, 2024
Metra

MeTra 99-7807 Car Audio Accessory

*For navigation models with dual zone automatic climate controls.
NOTE: Factory NAV screen not retained.
Visit www.MetraOnline.com for up-to-date vehicle specific applications.

KIT FEATURES

  • ISO DIN radio provision with pocket
  • Double DIN radio provision
  • 99-7807 painted Dark Charcoal and 99-7807T painted Taupe

KIT COMPONENTS

  • A) Radio housing trim panel
  • B) Brackets
  • C) Pocket
  • D) (4) #8 x 3/8″ Phillips pan-head screws
  • E) (10) #8 x 1/2″ Phillips screws

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: 70-1730 premium sound harness Antenna Adapter: 40-HD10

TOOLS REQUIRED

  • Panel removal tool
  • Phillips screwdriver

Attention! With the key out of the ignition, disconnect the negative battery terminal before installing this product. Ensure that all installation connections are secure before cycling the ignition to test this product.

DASH DISASSEMBLY

  1. Unclip and remove the trim panel from above the glove box located on the right side of the factory radio. (Figure A)

  2. Unclip and remove the trim panel located on the left side of the factory radio. (Figure B)

  3. Remove the (2) Phillips screws from the left and right side of the factory radio. (Figure C)

  4. Unsnap and remove the factory air vents located above the radio. (Figure D)

  5. Unclip and remove the top of the center console, including the cup holders. (Figure E)

  6. Remove (2) Phillips screws at the bottom edge of the pocket assembly. (Figure F)

  7. Remove (2) Phillips screws facing up inside of the pocket below the factory radio. (Figure G)

  8. Unclip and remove the pocket assembly. (Figure H)

  9. Remove (2) screws holding NAV disc player in place and remove it. (Figure I)

  10. Remove (2) screws facing up on the bottom of the factory radio. (Figure J)

ISO DDIN radio provision
  1. Unclip and remove the factory radio/ climate assembly. (Figure K)

  2. Remove (4) screws each and remove the climate control switches from the factory radio assembly. (Figure L)

  3. Remove the (2) factory panel clips on the factory radio and save for kit assembly. (Figure L)

KIT ASSEMBLY

ISO DIN radio provision with pocket
  1. Affix the (2) factory clips to the radio housing. (Figure A)

  2. Mount the climate switches to the radio housing using (6) of the #8 x 1/2″ screws on the upper and outside mounts. Do not install the screws on the bottom mounts shared by the radio brackets until installing the radio/ bracket assembly. (Figure A)

  3. Attach the pocket to the brackets with the (4) #8 x 3/8″ Phillips pan-head screws supplied. (Figure B)

  4. Slide the radio into the brackets and secure with screws provided with the aftermarket radio. (Figure C)

  5. Mount the radio assembly to the radio housing by installing (4) of the supplied #8 x 1/2″ screws to the shared radio brackets. (Figure D)

  6. Locate the factory wiring harness and antenna plug in the dash. Metra recommends using the proper mating adapters from Metra and AXXESS.

  7. Clip the new radio assembly into the dash and reassemble dash in reverse order of disassembly.

Double DIN radio provision
  1. Affix the (2) factory clips to the radio housing. (Figure A

  2. Mount the climate switches to the radio housing using (6) of the #8 x 1/2″ screws on the upper and outside mounts. Do not install the screws on the bottom mounts shared by the radio brackets until installing the radio/bracket assembly. (Figure A)

  3. Attach the radio to the brackets with the screws provided by the aftermarket radio. (Figure B)

  4. Mount the radio assembly to the radio housing by installing (4) of the supplied #8 x 1/2″ screws to the shared radio brackets. (Figure B)

  5. Locate the factory wiring harness and antenna plug in the dash. Metra recommends using the proper mating adapters from Metra and AXXESS.

  6. Clip the new radio assembly into the dash and reassemble dash in reverse order of disassembly.

Having difficulties? We’re here to help.

| Contact our Tech Support line at:
386-257-1187
---|---
| Or via email at:
techsupport@metra-autosound.com

Tech Support Hours (Eastern Standard Time)
Monday – Friday: 9:00 AM – 7:00 PM
Saturday: 10:00 AM – 7:00 PM
Sunday: 10:00 AM – 4:00 PM

® KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.edu or call 386-672-5771 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians

© COPYRIGHT 2021 METRA ELECTRONICS CORPORATION

www.MetraOnline.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals