GOLDEN LIGHTING 0511-1W Wall Sconce Wall Light Instruction Manual
- June 12, 2024
- GOLDEN LIGHTING
Table of Contents
Thank You for Choosing Golden Lighting
for Your Lighting Needs!
0511-1W Wall Sconce Wall Light
Pendants & Linear Pendants Above a
Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining
Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and
Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor.
Allow clearance for any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
Assembly Instructions: 0511-1W
How to Identify the Fixture’s Wires
Hot: Smooth, Black, or Transparent with Black Inner Thread
Hot: Smooth, Black, or Transparent with Black Inner Thread
Neutral: Ribbed, White or Transparent with White Inner Thread
Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
For Customer Service, contact the place of purchase to arrange for replacement
parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions:
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove old fixture from wall, including the old
mounting strap.
-
Mounting strap (A) contains several pairs of threaded holes and two sets of mounting screws (B & C). You may need to tighten the hex nuts that hold screws (B) in place.
-
Place mounting strap (A) up to your junction box.
Place backplate (D) over the mounting strap (A) lining up mounting screws (B) with the holes in backplate (D). This will allow you to ensure that you are hanging the fixture straight. -
Pull the house wires from the junction box and through the center of mounting strap (A). Secure mounting strap (A) to the junction box with mounting screws (C) and a screwdriver. Tighten the screws securely.
ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation. Please proceed to the next step.
CONNECTING THE WIRES -
Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION -
Place backplate (D) over mounting strap (A) so that mounting screws (B) protrude through the holes in backplate (D). Secure the backplate to the mounting strap with decorative nuts (F). Twist until the backplate of the fixture is snug against the wall.
-
old shade (H) up to socket (G) and secure in place using socket cover (I) and socket ring (J). Adjust the glass to horizontal and vertical. 7. Install a light bulb (not provided) into the socket (G) in accordance with the fixture’s specifications. Do not exceed maximum recommended wattage. Your installation is complete. Turn on the power and test the fixture.
@GoldenLighting
@GLFixtures
@GoldenLighting1
@GoldenLighting
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>