SERVER DFD-C Cereal Dispensers Instruction Manual

SERVER DFD-C Cereal Dispensers

Thank You for purchasing our CerealServ® Dispensers. Eliminate the waste of single-serve cereal packages. These robust dispensers easily dispense favorites with an ADA compliant handle – no twisting wrist motion or tight grasping required.

SAFETY

• According to food and safety regulations, most foods must be stored and/or served at certain temperatures or they could become hazardous.
• Check with local food and safety regulators for specific guidelines.
• Be aware of the product you are serving and the temperature the product is required to maintain. Server Products, Inc. cannot be responsible for the serving of potentially hazardous products.

IMPORTANT: Clean, rinse, sanitize, and dry parts daily or regularly to comply with local sanitization requirements.

CAUTION: Keep fingers clear of all moving parts to prevent operator injury when dispensing product, during cleaning, assembly and disassembly.

• NSF International listed.
• Does not require a twisting wrist motion or tight grasping to dispense.

CLEANING

YES! Use dishwashing soap and hot water

CLEAN

1. After disassembling, clean all washable parts with soap and hot water.
2. RINSE fully with clear water.
3. SANITIZE all parts according to local sanitization requirements. All parts in contact with food must be sanitized.
4. AIR DRY all parts fully.

Care of Countertop Stand & Drip Tray

• External surfaces may be wiped clean with a clean damp cloth.
• Glass and surface cleaners approved for use in food contact areas may be used.
• Do not use abrasive, caustic or ammonia-based cleansers.
• Do not use metal scrapers or cleaning pads that could scratch surfaces.

Plastic Drip Tray: HAND WASH ONLY.

CONFIGURATIONS

WALL-MOUNTED

• DFD-C-2
• DFD-C-3

1.5 LITER DISPENSERS

• 88930 Double with mounting bracket
• 88950 Triple with mounting bracket

3 LITER DISPENSERS

• 88940 Double with mounting bracket
• 88960 Triple with mounting bracket

COUNTERTOP

• DFD-C-ST

1.5 LITER DISPENSERS

• 88890 Double with countertop stand
• 88910 Triple with a countertop stand

3 LITER DISPENSERS

• 88900 Double with countertop stand
• 88920 Triple with a countertop stand

ASSEMBLY

WARNING: PRACTICE SAFETY. WASH ALL PARTS PROPERLY BEFORE USE.

ATTACH FRICTION PAD

• Insert four triangular tabs on the friction pad into matching slots in the cylinder.

INSTALL CYLINDER

• Slide the cylinder into the opening of the dispenser body.

INSTALL HANDLE ONTO BODY & CYLINDER

• Slide handle over both sides of body and cylinder.
• Snap handle centers into holes on each side.

INSTALL PIVOT PIN

• Slide the pivot pin into center hole on left side of handle.

ADD HOPPER TUBE

1. Insert tabs of hopper into slots on body.
2. Turn clockwise until secure.
3. Hopper snaps into place.
4. FILL THE UNIT WITH CEREAL
5. PUT THE LID ON TOP OF HOPPER.

MOUNTING

COUNTERTOP STAND

• Slide dispenser into bracket of stand.

WALL BRACKET INSTALLATION

YOU WILL NEED

• Screwdriver
• (4) screws &
• (4) anchor bolts (if needed)

Select wall location or sturdy vertical surface for mounting. Determine proper mounting hardware you will need to supply. Secure bracket to wall stud(s), anchor bolts in wall, or sturdy vertical surface.

USE

For the cylinder to advance and serve a portion, the handle must travel its full range of motion up and down.

• SWING HANDLE UP FULLY to load the cylinder chamber.

• Handle CLICKS above side notch.

• SWING HANDLEDOWN FULLY to dispense the serving.

• Angled tabs inside handle TAP bottom.

TROUBLESHOOTING

• Make sure there is enough product remaining to dispense and that the product is free to move to the bottom.
• Make sure you are dispensing the right kind of product. The CerealServ® dispenser is designed for free-flowing foods. Don’t use it for sticky, gummy or powdered ingredients.

DISASSEMBLY

1. REMOVE LID
2. EMPTY INGREDIENTS FROM UNIT
3. REMOVE HOPPER
4. Turn hopper counterclockwise to remove tabs from slots on body.
5. REMOVE PIVOT PIN
6. Rotate pin to the unlock position and take it out.

REMOVE HANDLE

• Lift handle upward to the position just before it would click. This makes the handle easier to remove.

1. REMOVE CYLINDER

2. REMOVE FRICTION PAD

CEREALSERV®

MOUNTING PARTS

• DOUBLE WALL MOUNTING BRACKET 89003
• TRIPLE WALL MOUNTING BRACKET 89005

INCLUDES

• DRIP TRAY ASSEMBLY 89014 & RUBBER FEET 84393

INCLUDES

• DRIP TRAY ASSEMBLY 89015 & RUBBER FEET 84393

DISPENSER PARTS

SERVER PRODUCTS LIMITED WARRANTY

2 YEAR WARRANTY

This Server product is backed by a two-year limited warranty against defects in materials and workmanship. See Server-Products.com for details.

GENERAL SERVICE, REPAIR OR RETURNS

Before sending any item to Server Products for service, repair, or return, contact Server Products customer service to request a Return Authorization Number. Merchandise must be sent to Server Products with this number. Service is extremely prompt. Typically, units are repaired and ship out within 48 hours of receipt. Merchandise being returned for credit must be in new and unused condition and not more than 90 days old and will be subject to a 20% restocking charge.

NEED HELP?

Server Products Inc

• 3601 Pleasant Hill Road Richfield, WI 53076 USA
• Chat with us: spsales@server-products.com
• TEL: 262.628.5600
• 800.558.8722

Please be prepared with your Model and Series Number. These are found on the side of the dispenser body and the stand or bracket. Certain components are also marked with individual Part Numbers.

References

• products.com
• Server Products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>