HUDSON VALLEY 5130 Sennett LED Chandelier Lighting Instruction Manual
- June 17, 2024
- HUDSON VALLEY
Table of Contents
HUDSON VALLEY
LIGHTING GROUP
Hudson Valley Lighting
Instruction Manual
5130 Sennett LED Chandelier Lighting
WARNING/CAUTION
- DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
- TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION ANDMAINTENANCE OF THIS UNIT HOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
- CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM.WASH HANDS AFTER USE.
- UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANYDAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
- PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.
| PA RT(S) | REPLACEMENT PART NAME | NUMBER |
|---|---|---|
| A,B,C,D,N | HARDWARE KIT | HDW-5130 |
| E | HEX NUTS | NUT-5130 |
| F | PLATE | PLA-5130 |
| G | CAP NUT | CPN-5130 |
| 1-1,1 | CANOPY ASSEMBLY | CAS-5130 |
| J | CHAIN | CHN-5130 |
| L | ALABASTER | ALA-5130 |
| M | DRIVER | DVR-5130 |
FIXTURE INSTALLATION
-
Slide crimp type CABLE CLAMP (N) onto the safety cable. Feed the SAFETY CABLE (O) down throughone of the holes in the top of the outlet box. Loop the SAFETY CABLE (O) over the approved support.Feed the SAFETY CABLE (O) back through the top of the box and the CABLE CLAMP (N). Using thecrimping tool, tightly crimp the CABLE CLAMP (N) to lock the SAFETY CABLE (O) in position.
-
Open the end link on the CHAIN (J) and attach to the loop on the FIXTURE ASSEMBLY (K) (WITHLED). Hang the FIXTURE ASSEMBLY (K) (WITH LED) on the CHAIN (J) at your desired height, andremove excess CHAIN (J).
-
Feed the wire through the CHAIN (J) , LOOP (I), CANOPY (H).
-
Pull the wire out of the Junction box and attach the MOUNTING PLATE (A) onto the junction boxusing the MOUNTING SCREWS (B). This fixture is designed to be mounted on heavy duty round or
octagon junction box rated for minimum 90 lbs. The junction box must be securely mounted to thestructure of the building. -
Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copperwire) or the GROUND SCREW (C) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE TO “HOT” WIRE FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH
-
With the DRIVER (M) in hand Connect the neutral DRIVER (M) lead to the neutral (Generally white)wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (D). Starting
1″ below the fastener, tightly wrap the connection with electrical tape so that the connections sealsthe end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRE OF STRANDS THAT COULDCAUSE A DANGEROUS SHORT CIRCUIT -
Connect the DRIVER (M) hot leads to the hot (Generally black) wire in the junction box. Fasten thejoined wires same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TOFOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH. Push electrical wires back into thejunction box
-
Lift up the CANOPY (H) up to the ceiling, and secure with HEX NUTS (E), placing the DRIVER (M) intothe CANOPY (H)
-
Open the top link on the CHAIN (J), and Hang the FIXTURE ASSEMBLY (K) (WITH LED) to the LOOP(I) on the CANOPY (H). Hide the excess wires and in the CANOPY (H). Attach the male connectorfrom fixture into the female connector from DRIVER (M).
-
Lift up the PLATE (F) and attach using the CAP NUT (G)
-
Restore power to the outlet at the breaker or fuse box.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>