HUDSON VALLEY B3616 Amire 16 Tall Wall Sconce Instruction Manual

HUDSON VALLEY B3616 Amire 16 Tall Wall Sconce

Product Information

Specifications:

• Brand: Hudson Valley Lighting
• Model: Amire B3620
• Fixture Type: Wall Sconce
• Max Wattage: Type B LED Lamp

Product Usage Instructions

Fixture Installation:

1. Loosen the mounting screws to remove the frame from the fixture assembly.
2. Determine the location of the lamp and mark the holes for the wall anchor using the mounting plate as a template.
3. Drill appropriate-sized holes for the wall anchor and install them.
4. Attach the mounting plate to the junction box using the mounting screws.
5. Connect the ground wire to the ground inside the outlet box and the white fixture leads to the neutral wire. Fasten the wires together with a wire nut and electrical tape.
6. Connect the black fixture leads to the hot wire in the junction box and fasten them together.
7. Apply weatherproof caulking or silicone sealant around the inside edge of the back to prevent water ingress.
8. Attach the fixture assembly to the mounting plate and secure it with mounting screws.
9. Screw the recommended type B LED lamp into the socket of the fixture.
10. Attach frame and silicone washer to the fixture assembly and secure it with screws.
11. Install glass pieces onto the fixture by pushing clips to hold them in place.
12. Restore power to the outlet at the breaker or fuse box.

Frequently Asked Questions (FAQ)

• Q: What type of bulb should be used with this fixture?
  A: This fixture is rated for a maximum-watt Type B LED lamp. Do not exceed the recommended wattage.

• Q: How should I secure the fixture to the wall?
  A: Follow the provided instructions to attach the fixture securely to the wall using the mounting plate, screws, and wall anchors.

WARNING/CAUTION

• DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
• TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURES MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY-TRAINED TECHNICIAN.
• CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USE.
• UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE BEFORE INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
• PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.

Installation Instructions

FIXTURE INSTALLATION

1. Loosen the MOUNTING SCREWS (G) to remove the FRAME (K) from the FIXTURE ASSEMBLY (H) .
2. Determine the location for the lamp. Using the mounting plate as a template, mark the location of the holes for the WALL ANCHOR (F).
3. Drill the appropriate size holes for the WALL ANCHOR (F). (the holes should be slightly smaller than the size of the anchors.) Install the wall anchors to the hole.
4. Attach the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B). This fixture is designed to be mounted on a standard junction box. The junction box must be securely mounted to the structure of the building. Screw in the WOOD SCREW (E) to the WALL ANCHOR (F).
5. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bare copper wire) or the GROUND SCREW (C) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE TO “HOT” WIRE! FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
6. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (D). Starting 1″ below the fastener, tightly wrap the connection with electrical tape so that the connection seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRES OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!
7. Connect the black fixture to the hot (Generally black) wire in the junction box. Fasten the joined wires the same as the previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
8. To prevent water from flowing into the outlet box, put a bead of weatherproof caulking or silicone sealant around the inside edge of the back. DO NOT PLUG THE DRAIN HOLE (N)!
9. Attach the FIXTURE ASSEMBLY (H) to the MOUNTING PLATE (A) and secure with the MOUNTING SCREWS (G).
10. Screw the BULB (J) up into the SOCKET of the fixture. THIS FIXTURE IS RATED FOR A MAX 8-WATT TYPE B LED LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE!
11. Attach the FRAME (K), and SILICONE WASHER (O) to the FIXTURE ASSEMBLY (H) and secure them with the SCREWS (G)
12. Install the GLASS A, B (L, M) to a fixture. pushing the clip to hold the glass.
13. Restore power to the outlet at the breaker or fuse box.

www.hvlgroup.com

References

• Hudson Valley Lighting Group

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>