HUDSON VALLEY LIGHTING GROUP B2917 Tehama 17 Inch Tall Wall Sconce Instruction Manual
- May 15, 2024
- HUDSON VALLEY LIGHTING GROUP
Table of Contents
Hudson Valley Lighting
Troy Lighting
Mitzi
Corbett Lighting
WARNING/CAUTION
- DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
- TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
- CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USE.
- UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
- PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.
SANTA CLARA
B2918
Installation Instructions
FIXTURE INSTALLATION
- Attach the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B). This fixture is designed to be mounted on standard round or octagon junction box. The junction box must be securely mounted to the structure of the building.
- Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the GROUND SCREW (C) on the MOUNTING PLATE (A). NEER CONNECT GROUND WIRE TO “HOT” WIRE FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH
- Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (D). Starting 1″ below the fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT
- Connect the black fixture leads to the hot (Generally black) wire in the junction box. Fasten the joined wires same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH. To prevent water from flowing into the outlet box, put a bead of weatherproof caulking or silicone sealant around the inside edge of the back. DO NOT PLUG THE DRAIN HOLE (M)
- Attach the FIXTURE ASSEMBLY (F) to the MOUNTING PLATE (A) and secure with the FIXTURE MOUNTING SCREWS (E).
- Screw the BULB (G) into the SOCKET of the fixture.THIS FIXTURE IS RATED FOR MAX 8 WATT TYPE T8 LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE
- Install the GLASS A,B,C (J,K,L) to fixture. pushing the clip to hold the glass.
- Close the top of the FIXTURE ASSEMBLY (F) and secure with the SILICONE WASHER (H), PLATE (I) and MOUNTING SCREWS (E).
- Restore power to the outlet at the breaker or fuse box.
| PART(S) | REPLACEMENT PART NAME | NUMBER |
|---|---|---|
| A,B,C,D | HARDWARE KIT | HDW-B2918 |
| E | FIXTURE MOUNTING SCREW | SCR-M |
| H | SILICONE WASHER | WAS-B2918 |
| I | PLATE | PLA-B2918 |
| J | GLASS A | GLS-B2918-A |
| K | GLASS B | GLS-B2918-B |
| L | GLASS C | GLS-B2918-C |
Documents / Resources
|
HUDSON VALLEY LIGHTING GROUP B2917 Tehama 17 Inch Tall Wall
Sconce
[pdf] Instruction Manual
B2917, B2918, B2917 Tehama 17 Inch Tall Wall Sconce, Tehama 17 Inch Tall Wall
Sconce, 17 Inch Tall Wall Sconce, Tall Wall Sconce, Wall Sconce, Sconce
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>