HUDSON VALLEY H891902 Georgann 16 Tall Wall Sconce Instruction Manual
- May 15, 2024
- HUDSON VALLEY
Table of Contents
HUDSON VALLEY H891902 Georgann 16 Tall Wall Sconce
Specifications
- Brand : Hudson Valley Lighting
- Model: Georgann H891902
- Fixture Type : Pendant Light
- Maximum Wattage : 15 Watts
Product Usage Instructions
Fixture Installation:
- Feed the wire through the STEM KIT (H) and twist tightly onto the FIXTURE ASSEMBLY (I). Add stems for desired hanging height.
- Slide the CANOPY (F) onto the STEM KIT (H) and thread the CONNECTOR (G) onto the top end of the STEM KIT (H).
- Pull the wire out from the junction box and install the MOUNTING PLATE (A) using MOUNTING SCREWS (B).
- Trim excess wire to a minimum of 6″ beyond the STEM, and strip each wire 5/8″.
- Attach Ground wire (Green) to the ground inside the outlet box or GROUND SCREW (C) on the MOUNTING PLATE (A).
- Connect the white fixture lead to the neutral wire in the outlet box using an approved WIRE NUT (D).
- Connect the black fixture leads to the hot wire in the outlet box using a WIRE NUT (D).
- Secure CANOPY (F) to ceiling with BOLT NUT (E).
- Screw METAL SHADE (K) to FIXTURE ASSEMBLY (I).
- Screw BULB (J) up into the SOCKET of the fixture, ensuring not to exceed the maximum 15-watt rating.
- Restore power at the breaker or fuse box.
FAQ
- Q: What type of lamp can be used with this fixture?
- A : This fixture is rated for a maximum 15-watt Type A lamp. Do not exceed the recommended wattage.
- Q: How should I connect the wires during installation?
- A : Connect the white fixture lead to the neutral wire and the black fixture lead to the hot wire. Ensure proper insulation and connections to avoid short circuits.
- Q: What should I do if I encounter any issues during installation?
- A : If you face any difficulties or uncertainties during installation, please refer to the provided manual or contact customer support for assistance.
WARNING/CAUTION
- DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION. · TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURES MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY-TRAINED TECHNICIAN. · CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER
- REPRODUCTIVE HARM. WASH HANDS AFTER USE. · UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS. · PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.
FIXTURE INSTALLATION
- Feed the wire through the STEM KIT (H) and twist tightly onto the FIXTURE ASSEMBLY (I). Keep adding additional stems until your desired hanging height is met.
- Slide in CANOPY (F) onto the STEM KIT (H), and thread the CONNECTOR (G) onto the top end of the STEM KIT (H).
- Pull the wire out from the junction box, and install the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B). This fixture is designed to be mounted on a standard round or octagon junction box. The junction box must be securely mounted to the structure of the building.
- Trim off the excess wire to a minimum 6″ beyond the STEM and strip each wire 58″.
- Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bare copper wire) or the GROUND SCREW (C) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE TO “HOT” WIREĞ FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH.
- Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wire together with an approved fastener ( WIRE NUT) (D). Starting 1″ below the fastener, tightly wrap the connection with electrical tape so that the connection seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRES OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUITĞ
- Connect the black fixture leads to the hot (Generally black) wire in the outlet box. Fasten the joined same as the previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH
- Push the wires back into the junction box. Lift up the CANOPY (F) up to the ceiling, and secure it with the BOLT NUT (E).
- Screw the METAL SHADE (K) to the FIXTURE ASSEMBLY (I) of the fixture. 10. Screw the BULB (J) up into the SOCKET of the fixture. THIS FIXTURE IS RATED FOR MAX 15 TYPE A LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGEĞ11. Restore power to the outlet at the breaker or fuse box.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>