HUDSON VALLEY 7123 LED Flush Mount Geraldton Instruction Manual

Table of Contents

HUDSON-VALLEY-7123-LED-Flush-Mount-Geraldton-product

Product Usage Instructions

Fixture Installation

Attach the MOUNTING PLATE (A) (WITH LED) onto the junction box using the MOUNTING SCREWS (B). This fixture is designed to bemounted on a standard round or octagon junction box. The junction box must be securely mounted to the structure of the building.
Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bare copper wire) or the GROUND SCREW (C) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE TO HOT WIRE. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH.
Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (D). Starting 1 inch below the fastener, tightly wrap the connection with electrical tape so that the connection seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRES OR STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT.
Connect the black fixture leads to the hot (Generally black) wire in the junction box. Fasten the joined wires same as the previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH.
Install the GLASS (I) into RING (H), pushing the clip to hold the GLASS (I).
Attach the RING (H) to the MOUNTING PLATE (A) (WITH LED) and secure it with the SET SCREWS (E).
Restore power to the outlet at the breaker or fuse box.

Q: What should I do if there are exposed wires or strands after connecting them?
- A: Make sure to tightly wrap the connection with electrical tape so that the connection seals the end of the fastener. This will prevent any exposed wires or strands that could cause a dangerous short circuit.
Q: Can I connect the ground wire to the hot wire?
- A: No, you should never connect the ground wire to the hot wire. This can result in serious injury or death. Always follow the instructions provided.
Q: Is it important to securely mount the junction box to the structure of the building?
- A: Yes, it is important to securely mount the junction box to ensure proper stability and safety of the fixture.
Q: Can I reverse the hot and neutral wires?
- A: No, you should never reverse the hot and neutral wires. This can result in serious injury or death. Always follow the instructions provided

WARNING/CAUTION

DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE
- INSTALLATION AND MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE
- HARM. WASH HANDS AFTER USE.
UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR
- ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.

HUDSON-VALLEY-7123-LED-Flush-Mount-Geraldton-
fig-1

FIXTURE INSTALLATION

Attach the MOUNTING PLATE (A) (WITH LED) unto the junction box using the MOUNTING SCREWS (B). This fixture is designed to be mounted on standard round or octagon junction box. The junction box must be securely mounted to the structure of the building.
Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the GROUND SCREW (C) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE TO “HOT” WIRE! FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (D). Starting 1″ below the fastener, tightly wrap the connection with electrical tape so that the connection seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!
Connect the black fixture leads to the hot (Generally black) wire in the junction box. Fasten the joined wires same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
Install the GLASS (I) into RING (H), pushing the clip to hold the GLASS (I).
Attach the RING (H) to the MOUNTING PLATE (A) (WITH LED) and secure with the SET SCREWS (E).
Restore power to the outlet at the breaker or fuse box.