HUDSON VALLEY 2203-VGL-WP Marabec Three Light Wall Sconce Instruction Manual

HUDSON VALLEY 2203-VGL-WP Marabec Three Light Wall Sconce

Product Information

Specifications:

• Brand: Hudson Valley Lighting
• Model: Marabec 2203
• Fixture Type: Ceiling Light
• Compatible Bulb Type: Type B Lamp
• Maximum Wattage: Not specified
• Replacement Part Name: Hardware Kit – Ball Nut
• Replacement Part Number: HDW-01 NUT-2203
• Website: www.hvlgroup.com

Installation Instructions:

Fixture Installation:

1. Attach the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B).
2. Thread the STUDS (C) onto the MOUNTING PLATE (A), adjust its threads so that 136 of the thread extends beyond the backplate of the FIXTURE ASSEMBLY (H), and secure using HEX NUT (D). The junction box must be securely mounted to the structure of the building.
3. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bare copper wire) or the GROUND SCREW (E) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE TO HOT WIRE. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH.
4. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (F). Starting 1″ below the fastener, tightly wrap the connection with electrical tape so that the connection seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRES OR STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT.
5. Connect the black fixture leads to the hot (Generally black) wire in the junction box. Fasten the joined wires same as the previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH.
6. Attach the FIXTURE ASSEMBLY (H) to the MOUNTING PLATE (A) using BALL NUT (G).
7. Screw the BULB (I) into the SOCKET of the FIXTURE ASSEMBLY (H). THIS FIXTURE IS RATED FOR TYPE B LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE.
8. Restore power to the outlet at the breaker or fuse box.

FAQ:

• Q: What type of bulb does this fixture use?
  A: This fixture is compatible with Type B lamps.

• Q: What is the maximum wattage for this fixture?
  A: The maximum wattage is not specified. Please do not exceed the recommended wattage for the bulb used.

• Q: Where can I find replacement parts for this fixture?
  A: You can visit our website at www.hvlgroup.com for replacement parts. The replacement part name is Hardware Kit – Ball Nut, and the part number is HDW-01 NUT-2203.

WARNING/CAUTION

• DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
• TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURES MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY-TRAINED TECHNICIAN.
• CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USE.
• UNPACK FIXTURE, PARTS, AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE BEFORE INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
• PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.

FIXTURE INSTALLATION

1. Attach the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B). Thread the STUDS (C) unto the MOUNTING PLATE (A), adjust its threads so that 316″ of the thread beyond the backplate of the FIXTURE ASSEMBLY (H), and secure using HEX NUT (D). The junction box must be securely mounted to the structure of the building.
2. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bare copper wire) or the GROUND SCREW (E) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE TO “HOT” WIREĞ FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH.
3. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wire together with an approved fastener (WIRE NUT) (F). Starting 1″ below the fastener, tightly wrap the connection with electrical tape so that the connection seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT.
4. Connect the black fixture leads to the hot (Generally black) wire in the junction box. Fasten the joined wires the same as the previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH.
5. Attach the FIXTURE ASSEMBLY (H) to the MOUNTING PLATE (A) using BALL NUT (G).
6. Screw the BULB (I) into the SOCKET of the FIXTURE ASSEMBLY (H). THIS FIXTURE IS RATED FOR ŁWATT TYPE B LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE.
7. Restore power to the outlet at the breaker or fuse box.

www.hvlgroup.com

References

• Hudson Valley Lighting Group

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>