The Decora Smart Z-WaveTM 800 Series Switch is designed for use with modern Z-Wave hubs and makes it easier than ever to control your lights how you want. This switch is compatible with any Z-Wave-enabled network, regardless of the manufacturer, and can also be used with other devices displaying the Z-Wave logo. As well, this device can act as a repeater to increase the reliability of the Z-Wave network. The Decora Smart Z-Wave 800 Series Switch looks right at home with your other Decora® in-wall devices and features intuitive on/off control. Add the switch to your Z-Wave hub of choice to enable app commands, scheduling, and voice control of connected lighting.

We are here to help

Your switch works with

General purpose loads up to 15A, for specific ratings, see the chart below.
Do not use your switch with metal wallplates or aluminum wire.
Additional self-service support options can be found at leviton.com/decorasmart

RATINGS

Features

What you need to make it work

A Z-Wave compatible hub.
A Z-Wave mesh network to join. Ensure your device is installed within 50 ft of the hub or another Z-Wave-enabled repeater. Communication through exterior surfaces may reduce transmission distances.
An available interior switch wall box with a line (hot), load, neutral, and ground wire.
To control the switch from more than one location such as in a 3-way or multi-way, you will need a wired DD0SR Companion device. Learn more about Companion devices and ﬁnd connection instructions at leviton.com/decorasmart

Identify your wires

WARNING: TO AVOID FIRE, SHOCK, OR DEATH, turn OFF power at the circuit breaker.

Check your wall box

Remove wallplate and disconnect existing switch.
Restore power. Carefully test wires with voltage tester to ﬁnd the line (hot) wire.
Turn OFF power at the circuit breaker.
Mark the wires as shown below. Please note neutral wires are required to operate this device. Quick tip: Neutral wires are typically white and will be found bundled inside the electrical box.

If your wallbox looks different, call an electrician.

Wire your switch

Single-pole installation

Work only one connection at a time.
Connect wires as shown using the included wire connectors.

NOTES

Neutral connection is required.
The YELLOW/RED traveler wire is only used in 3-way applications; remember to put a wire connector on the YELLOW/RED traveler even if not in use.

If your wallbox contains a different wiring configuration, contact Leviton’s technical support team or consult an electrician.

Test and install

Restore power.
After powering ON the switch to confirm it is receiving power, turn the power back OFF again at the breaker prior to completing the installation.
WARNING: Turn OFF power at the circuit breaker before screwing in your switch.
Gently push wires into wallbox. Screw switch to box.
Snap on Decora walllplate and restore power.

Congratulations! Your Decora Smart Switch is ready to control your light.

SmartStart

Your Decora Smart Z-Wave 800 Series Switch is compatible with SmartStart. SmartStart enabled devices can be added to a Z-Wave network by scanning the Z-Wave QR code on the top of the device, on the strap, or on the back of the unit box with a compatible Z-Wave controller that supports SmartStart inclusion. The device should be added automatically within 10 minutes of being switched on and in the network vicinity.

The QR code label with DSK is located on the top of the device. If required, the PIN code is underlined on the label. The PIN code is also located on the front strap.

Setup mode

Enter setup mode

Hold the top rocker for 7 seconds. The Status LED will turn AMBER, release and the Status LED will blink AMBER.
The device is now in setup mode.

Exit setup mode

Hold the top rocker for 7 seconds until the LED turns AMBER. The device will return to normal operation.

Adding the Decora Smart Z-Wave 800 Series Switch to a hub
When using a Z-Wave Plus certified hub, choose network-wide inclusion or SmartStart. If network-wide inclusion does not discover your device, try classic inclusion.

Network-Wide Inclusion to a Z-Wave Network

Network Wide Inclusion allows your device to be included in the network using devices already paired to your home automation hub. Start with the devices closest to the hub and work your way outward.

Enter setup mode (see page 10).
Tap the top rocker 1 time. The Status LED will quickly flash GREEN. The device is now ready to learn into the Z-Wave network.
Use the Z-Wave controller to complete the device enrollment process (follow the Z-Wave controller instructions)
The device’s Status LED will turn OFF and then flash GREEN 4 times to confirm it has been successfully added to a Z-Wave network. If the device was not successfully added, the Status LED will flash RED 4 times.

Classic inclusion to a Z-Wave network

For older controllers, Classic Inclusion is supported. Depending on the age of the controller it may need to be 3 to 35 feet from the device when including.

Enter setup mode (see page 10).
Follow the Z-Wave controller instructions to enter inclusion mode.
Tap the top rocker 1 time, the Status LED will quickly flash GREEN.
The Z-Wave controller will confirm successful inclusion to the Z-Wave network.

Exclusion from a Z-Wave network

The Exclusion command found in the Z-Wave controller is used as a best practice for removing devices from a Z-Wave network.

Enter setup mode (see page 10).
Follow the Z-Wave controller instructions to enter exclusion mode.
Tap the top rocker 1 time, the Status LED will quickly flash GREEN.
The Z-Wave controller will confirm successful exclusion from the Z-Wave network.

Customization

Status LED

Follow the below steps to change the functionality of the Status LED.

Status LED ON when load is ON

Enter setup mode (see page 10).
Tap the top rocker 4 times. The Status LED will quickly flash GREEN/AMBER.
Tap the top rocker 1 time. The Status LED will flash GREEN 4 times to confirm the selection.

Status LED ON when load is OFF (default)

Enter setup mode (see page 10).
Tap the top rocker 4 times. The Status LED will quickly flash GREEN/AMBER.
Tap the top rocker 2 times. The Status LED will flash AMBER 4 times to confirm the selection.

Status LED OFF

Enter setup mode (see page 10).
Tap the top rocker 4 times. The Status LED will quickly flash GREEN/AMBER.
Tap the top rocker 3 times. The Status LED will flash RED 4 times to confirm the selection.

ZW15S indicator function
Supports the indicator command class with indicator ID 0x50 (identify). When an indicator command is received the Status LED on the device will quickly flash GREEN.

Advanced options
Your device supports Over-the-Air updates using the Z-Wave Firmware Update Meta Data command class for standardized firmware updates. The following advanced options can be configured over the Z-Wave network by a compatible Z-Wave controller.

Status LED configuration

Parameter No: 7, Length: 4 Byte
Valid Values = 0 to 255 (default 255)
0 = Status LED OFF
254 = Status LED ON when load is ON
255 = Status LED ON when load is OFF (locator mode)

ZW15S supported associations and supported Z-Wave classes

Group number: 1

Maximum Nodes : 5
Name: Lifeline
A notification is sent to the nodes in this association group when a Lifeline event occurs.
All nodes in the association group receive notification of status changes.
Profile: 0x0001
Command Class Associations
0x5A01: COMMAND_CLASS_DEVICE_RESET_LOCALLY, DEVICE_RESET_LOCALLY_NOTIFICATION
0x2503: COMMAND_CLASS_SWITCH_BINARY_V2, SWITCH_BINARY_REPORT_V
0x8703: COMMAND_CLASS_INDICATOR (0x87) and INDICATOR_REPORT_V3 (0x03)

Group number: 2

Maximum Nodes : 5
Name: Binary switch set
All nodes in the association group receive a command based on ON/OFF button presses.
Profile: 0x2001
Command Class Associations
0x2501: COMMAND_CLASS_SWITCH_BINARY.SWITCH_BINARY_SET

Advanced options (continued)

Group number: 3

Maximum Nodes: 5
Name: Basic set
All nodes in the association group receive a command based on ON/OFF button presses.
Profile: 0x2001
Command Class Associations
0x2001: COMMAND_CLASS_BASIC.BASIC_SET

The BASIC command class is mapped to the binary switch class, as follows:

Basic Set maps to Binary Switch Set
Basic Get maps to Binary Switch Get
Basic Report maps to Binary Switch Report

Supports the following additional Z-Wave classes

SWITCH BINARY v2 secured
Z-WAVE PLUS INFO v2 non-secured
ASSOCIATION v2 secured
ASSOCIATION GRP INFO v3 secured
S2 SECURITY v1 non-secured
VERSION v3 secured
MANUFACTURER SPECIFIC v2 secured
CONFIGURATION v4 secured
DEVICE RESET LOCALLY v1 secured
POWER LEVEL v1 secured
BASIC v2 secured
SCENE ACTUATOR CONF v1 secured
SCENE ACTIVATION v1 secured
TRANSPORT SERVICE v2 non-secured
FIRMWARE UPDATE MD v5 secured
SUPERVISION v1 non-secured
INDICATOR v3 secured
MULTI-CHANNEL ASSOCIATION v3 secured

Factory default

When removing a Z-Wave device from the network, it is best practice to use the exclusion process. In situations where a device needs to be returned to factory default settings, follow the steps below. Please use this procedure only when the network primary controller is missing or otherwise inoperable.

Hold the top rocker for 14 seconds: After the first 7 seconds, the Status LED will turn AMBER. Continue holding until the Status LED flashes RED/AMBER then release.
The device will reset.

What to do if…

Switch is wired and installed but the light does not respond:

Make sure power has been restored at the circuit breaker.
Verify wiring connections are correct.

When power is applied to the switch, the light is OFF and does not respond:

For proper operation the switch needs a line (hot), neutral, load, and ground connection.
Confirm the white conductor is a neutral.

My lights work but they are flickering:

Unscrew light bulb and test with voltage tester to make sure a line (hot) and neutral wire are connected to the light.

How do I clean my device?

To clean, use a damp cloth with mild soap. DO NOT use disinfecting products, including foggers, sprays or other types of atomized cleaning agents. Visit leviton.com/decorasmart or contact technical services for additional help.

Safety first

WARNINGS:

TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring!
TO AVOID FIRE, PERSONAL INJURY OR PROPERTY DAMAGE, DO NOT install to control a receptacle.
This product is to be installed and/or used by electrical codes and regulations.
For indoor use only.
If you are unsure about any part of these instructions, consult an electrician.

CAUTIONS

The Decora Smart branded ZW15S is not compatible with standard 3-way or 4-way switches. Use only (1) Decora Smart branded ZW15S switch in a wired multi-location circuit with up to 9 DD0SR-01Z Switch Companions or up to 4 DD0SR-DLZ Switch Companions.
Maximum wire length from the switch to all installed companion devices cannot exceed 300 ft (90m).
Save this instruction sheet. It contains important technical data along with testing and troubleshooting information which will be useful after installation is complete.
The recommended minimum wall box depth is 2-3/4 in.
Use this switch with copper or copper-clad wire only.

ADDITIONAL RATINGS

Purpose of control : Operating Control
Action Control Type : 1
Pollution Degree : 2
Impulse Voltage : 2500V
Disconnection Type : Micro

Limited 2 year warranty & exclusions

For Leviton’s limited product warranty, go to www.leviton.com. For a printed copy of the warranty, call 1-800-824-3005.

FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada ULC to the attention of the Quality Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec),

FCC COMPLIANCE STATEMENT
The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (i.) This device may not cause harmful interference (ii.) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by Leviton could void the user’s authority to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC CAUTION
Any changes or modifications not expressly approved by Leviton Manufacturing Co., Inc., could void the user’s authority to operate the equipment. FCC SUPPLIER’S DECLARATION OF CONFORMITY Model ZW15S – Z-Wave Switch is manufactured by Leviton Manufacturing Co., Inc. 201 N. Service Road, Melville, NY 11747. www.leviton.com. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IC STATEMENT
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

RF EXPOSURE AND CO-LOCATION
To comply with FCC OET Bulletin 65 and ISED RF exposure limits for general population and uncontrolled exposure, this device shall be installed and operated with a minimum distance of 7.9 inches (20 cm) between the radiator and your body. Also, must not be co-located or operated in conjunction with any other antenna or transmitter.

PATENT INFORMATION
Patents covering this product, if any, can be found on Leviton.com/patents.

COPYRIGHT AND TRADEMARK INFORMATION
Decora and Decora Smart are the registered trademarks of Leviton Manufacturing Co., Inc., registered in the U.S., Canada, Mexico, and China. Z-Wave and Z-Wave Plus are registered trademarks of the Z-Wave Alliance. Use herein of other third-party trademarks, service marks, trade names, brand names and/or product names are for informational purposes only, are/may be the trademarks of their respective owners; such use is not meant to imply affiliation, sponsorship, or endorsement. No part of this document may be reproduced, transmitted or transcribed without the express written permission of Leviton Manufacturing Co., Inc.