Yale YRD654-ZW3 Z-Wave Plus v2 Assure Lock 2 Instruction Manual

Yale YRD654-ZW3 Z-Wave Plus v2 Assure Lock 2

Smart Module Installation

Z-Wave Plus™ v2 Assure Lock® 2
Models: YRD410, YRD420, YRD430, YRD450, YRD420-F, YRD450-F

NOTE:
Anytime you add or remove a Smart Module from your lock, the batteries must be removed.

1. If your lock is already installed, remove the batteries.

2. Insert the Yale Z-Wave Plus™ v2 Smart Module into the battery compartment slot.
   Reinsert the batteries.

3. Open the Yale Access App and navigate to your lock model.

   • 3a. Select ‘Lock Settings’.
   • 3b. Select ‘Yale Smart Module’.
   • 3c. Follow the steps in the app to complete the setup.

4. To remove the Yale Z-Wave Plus™ v2 smart module from your system, select the disconnect Z-Wave™ option from the lock settings in the Yale Access App.

Anytime you add or remove a Smart Module from your lock, the batteries must be removed.

Z-Wave Plus™ v2 Assure Lock®
Models: YRD216, YRD226, YRD256, YRL226, YRL216

1. If your lock is already installed, remove the batteries.

2. Insert the Yale Z-Wave Plus™ v2 Smart Module into the battery compartment slot.
   Reinsert the batteries.

3. If you have SmartStart enabled with your Z-Wave™ system, follow the in-app prompts to add a new device. If you do not have SmartStart or are not sure, follow the steps below.

   • 3a. Enter your locks master entry code, followed by the
   • 3b. Press the 7 key followed by the
   • 3c. Press the 1 key followed by the

4. To remove the Z-Wave Plus™ v2 Smart Module from your system, open the smart home or alarm app and follow the instructions for removing a device.

   • 4a. Enter your locks master entry code, followed by the
   • 4b. Press the 7 key followed by the
   • 4c. Press the 1 key followed by the

Anytime you add or remove a Smart Module from your lock, the batteries must be removed.

Changes or modifications to this device, not expressly approved by MASTER LOCK Group could void the user’s authority to operate the equipment.

This device is a security-enabled Z-Wave Plus™ v2 product that can use encrypted Z-Wave Plus™ v2 messages to communicate with other security-enabled Z-Wave Plus™ v2 products. This device must be used in conjunction with a Security Enabled Z-Wave™ Controller to fully utilize all implemented functions. This product can be operated in any Z-Wave™ network with other Z-Wave™ certified devices from other manufacturers. All non-battery-operated nodes within the network will act as repeaters regardless of vendor to increase the reliability of the network.

FCC STATEMENT

Class B Equipment
This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS.

1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
2. THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

This equipment complies with the FCC radiation limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

Industry Canada:

Section 7.1.2 of RSS-GEN
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Section 7.1.3 of RSS-GEN
This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device.

24/7 1-855-213-5841 Yale Home ShopYaleHome.com.

Yale® is a registered trademark of Master Lock Company LLC and its affiliates. Other products’ brand names may be trademarks or registered trademarks of their respective owners and are mentioned for reference purposes only. © Copyright 2023. All rights reserved. Reproduction in whole or part without the express written permission of Master Lock Company LLC and its affiliates is prohibited.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>