Enerlites 65300 30A Flush Mount Power Outlet Installation Guide
- June 14, 2024
- ENERLITES
Table of Contents
Enerlites 65300 30A Flush Mount Power Outlet
Product Information
- Specifications
- Model: SFDFQUBDMF
- Wire Compatibility: #10 AWG thru #4 AWG copper, copper-clad or aluminum wire
- Wire Configuration: 2 Pole, 3 Wire, Grounding
- Torque for Terminal Screws: 30 in-lbs
Product Usage Instructions
- Left Side Connection
- Connect the left side of the product to the corresponding left-side connection of your electrical system.
- Right Side Connection
- Connect the right side of the product to the corresponding right side connection of your electrical system.
- Green Ground Connection
- Connect the green ground wire of the product to the grounding system of your electrical system.
- Note: Ensure that the product is not used with single-gang wall boxes, single-gang mud rings, or single-gang box extenders.
- Note: Tighten the terminal screws to 30 in-lbs of torque for proper connection.
- Frequently Asked Questions (FAQ)
- Q: Can I use this product with single-gang wall boxes?
- A: No, this product should not be used with single-gang wall boxes, single-gang mud rings, or single-gang box extenders.
- Q: What size of wire is compatible with this product?
- A: This product is compatible with #10 AWG through #4 AWG copper, copper-clad, or aluminum wire.
- Q: How much torque should I apply to the terminal screws?
- A: Tighten the terminal screws to 30 in-lbs of torque.
WARNING: Turn the POWER OFF at the circuit breaker before installing the
receptacle. Read and understand these instructions before installing. This
device is intended for installation in accordance with the National Electric
Code and local regulations. It is recommended that a qualified electrician
perform this installation. Make sure to turn off the circuit breaker or fuses)
and make sure the power is off before wiring the device.
WARNING: DO NOT use single-gang wall boxes, single-gang mud rings, or
single-gang box extenders.
NOTE: for use with #10 AWG thru #4 AWG copper, copper-clad, or aluminum
wire. Tighten terminal screws to 30 in-Ibs of torque.
WIRING DIRECTIONS
- Connect the RED /HOT wire to the left side terminal and tighten the screw
- Connect the BLACK /HOT wire to the right side terminal and tighten the screw
- Connect the GREEN/GROUND wire to the GROUND terminal and tighten the screw.
WARRANTY INFORMATION
- This device is warranted to be free of material and workmanship defects for 2 years from the date of purchase.
- An original receipt or proof of purchase from an authorized retailer must be presented upon warranty claim.
- ALL claims must be verified and approved by Enerlites, Inc. Warranties from other Enerlites products may vary.
- This warranty is non-transferable and does not cover normal wear and tear or any malfunction, failure, or defect resulting from misuse, abuse, neglect, alteration, modification, or improper installation.
- To the fullest extent permitted by the applicable state law, Enerlites shall not be liable to the purchaser or end-user customer of Enerlites products for direct, indirect, incidental, or consequential damages even if Enerlites has been advised of the possibility of such damages.
- Enerlites’ total liability under this or any other warranty, express or implied, is limited to repair, replacement, or refund.
- Repair, replacement, or refund are the sole and exclusive remedies for breach of warranty or any other legal theory.
CONTACT
- © 2021 Enerlites, Inc. CA, U.S.A.
- WWW.ENERLITES.COM.
- 0212210187
- NEMA 6-30R
- 2 Pole, 3 Wire, Grounding
- Rated at 30A 250 VAC, 60Hz
- MODEL 65300
- 30A Flush Mount Power Outlet
Read User Manual Online (PDF format)
Loading......