Yale YRD420-F-ZW3 Assure Lock and Z-Wave System Smart Module User Guide
- May 15, 2024
- Yale
Table of Contents
Yale®Z-Wave
Plus™ Smart Module
Installation Guide
YRD420-F-ZW3 Assure Lock and Z-Wave System Smart Module
Please use this procedure only when network primary controller is missing or otherwise inoperable.
Adding a Yale Z-Wave Plus™ v2 Smart Module to your Assure Lock & Z-Wave™ System
-
Install Yale Smart Module into slot above battery compartment
IMPORTANT: Batteries must be removed before inserting Yale Smart Module:
• Remove battery cover
• Remove batteries
• Insert Yale Smart Module
• Reinstall batteries
• Reinstall battery cover
-
Open Z-Wave™ system’s smart home or alarm app on your smartphone or tablet
-
If you have SmartStart* enabled with your Z-Wave™ System follow in-app prompts to add a new device If you don’t have SmartStart or are not sure, follow steps 4 – 6
-
On your lock keypad, enter your master entry code followed by the icon If prompted, scan QR code
-
Press the 7 key followed by the icon
-
Press the 1 key followed by the icon
Removing a Yale Z-Wave Plus™ v2 Smart Module from your Assure Lock & Z-Wave™ System
-
Open Z-Wave™ system’s smart home or alarm app and follow instructions for removing a device
-
On your lock keypad, enter your master entry code followed by the icon
-
Press the 7 key followed by the icon
-
Press the 3 key followed by the icon
-
Remove Yale Smart Module from slot above battery compartment
IMPORTANT: Batteries must be removed before removing Yale Smart Module:
• Remove battery cover
• Remove batteries
• Remove Yale Smart Module
• Reinstall batteries
• Reinstall battery cover -
If you’re adding a new Yale Smart Module, follow instructions included with it
*SmartStart enabled products can be added into a Z-Wave network by scanning the Z-Wave QR Code present on the product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in network vicinity.
Warning: Changes or modifications to this device, not expressly approved by
ASSA ABLOY Residential Group could void the user’s authority to operate the
equipment.
This device is a security enabled Z-Wave Plus™ v2 product that is able to use
encrypted Z-Wave Plus™ v2 messages to communicate to other security enabled
Z-Wave Plus™ v2 products. This device must be used in conjunction with a
Security Enabled Z-Wave™ Controller in order to fully utilize all implemented
functions. This product can be operated in any Z-Wave™ network with other
Z-Wave™ certified devices from other manufacturers. All non-battery operated
nodes within the network will act as repeaters regardless of vendor to
increase reliability of the network.
FCC :
Class B Equipment
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful Interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS. (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Industry Canada:
Section 7.1.2 of RSS-GEN Under Industry Canada regulations, this radio
transmitter may only operate using an antenna of a type and maximum (or
lesser) gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication.
Section 7.1.3 of RSS-GEN This Device complies with Industry Canada License-
exempt RSS standard(s).
Operation is subject to the following two conditions: 1) this device may not
cause interference, and 2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada RSS standard exemptes de
licence(s). Son fonctionnement est soumis aux deux conditions suivantes: 1) ce
dispositif ne peut causer des interférences, et 2) cet appareil doit accepter
toute interférence, y compris les interférences qui peuvent causer un mauvais
fonctionnement du dispositif.
CAN ICES-3B/NMB-3B
Yale Locks & Hardware
24/7 Tech Support: 1-855-492-0505
www.yalehome.com
Yale® is a registered trademark of ASSA ABLOY Residential Group. Other
products’ brand names may be trademarks or registered trademarks of their
respective owners and are mentioned for reference purposes only. © Copyright
2020. All rights reserved. Reproduction in whole or in part without the
express written permission of ASSA ABLOY Residential Group is prohibited.
P/N
AYR-MOD-ZW3-MNL-0015 Rev A
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>